24LC164/SN Microchip Technology, 24LC164/SN Datasheet - Page 7

• Manufacturer Part Number: 24LC164/SN
• Description: IC EEPROM 16KBIT 400KHZ 8SOIC
• Manufacturer: Microchip Technology

Specifications of 24LC164/SN

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 16K (2K x 8)
• Speed: 100kHz, 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 8-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification

5.0
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete (this feature can be used to maximize bus
throughput). Once the stop condition for a write com-
mand has been issued from the master, the device ini-
tiates the internally timed write cycle. ACK polling can
be initiated immediately. This involves the master send-
ing a start condition followed by the control byte for a
write command (R/W = 0). If the device is still busy with
the write cycle, then no ACK will be returned. If the
cycle is complete, then the device will return the ACK
and the master can then proceed with the next read or
write command. See Figure 5-1 for flow diagram.
FIGURE 5-1:
6.0
The 24LC164 can be used as a serial ROM when the
WP pin is connected to V
inhibited and the entire memory will be write-protected.
 2004 Microchip Technology Inc.
ACKNOWLEDGE POLLING
WRITE PROTECTION
Initiate Write Cycle
Send Control Byte
Write Command
with R/W = 0
Acknowledge
Condition to
Send Stop
(ACK = 0)?
Did Device
Send Start
Operation
Send
Next
ACKNOWLEDGE
POLLING FLOW
Yes
CC
. Programming will be
No
7.0
Read operations are initiated in the same way as write
operations with the exception that the R/W bit of the
slave address is set to ‘1’. There are three basic types
of read operations: current address read, random read
and sequential read.
7.1
The 24LC164 contains an address counter that main-
tains the address of the last word accessed, internally
incremented by one. Therefore, if the previous access
(either a read or write operation) was to address n, the
next current address read operation would access data
from address n + 1. Upon receipt of the slave address
with R/W bit set to ‘1’, the 24LC164 issues an acknowl-
edge and transmits the 8-bit data word. The master will
not acknowledge the transfer but does generate a stop
condition and the 24LC164 discontinues transmission
(Figure 7-1).
7.2
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, first the word address must
be set. This is done by sending the word address to the
24LC164 as part of a write operation. After the word
address is sent, the master generates a start condition
following the acknowledge. This terminates the write
operation, but not before the internal address pointer is
set. Then the master issues the control byte again but
with the R/W bit set to a ‘1’. The 24LC164 will then
issue an acknowledge and transmits the 8-bit data
word. The master will not acknowledge the transfer but
does generate a stop condition and the 24LC164 dis-
continues transmission (Figure 7-2).
7.3
Sequential reads are initiated in the same way as a ran-
dom read except that after the 24LC164 transmits the
first data byte, the master issues an acknowledge as
opposed to a stop condition in a random read. This
directs the 24LC164 to transmit the next sequentially
addressed 8-bit word (Figure 7-3).
To provide sequential reads the 24LC164 contains an
internal address pointer which is incremented by one at
the completion of each operation. This address pointer
allows an entire device memory contents to be serially
read during one operation.
7.4
The 24LC164 employs a V
which disables the internal erase/write logic if the V
is below 1.5 volts at nominal conditions.
The SCL and SDA inputs have Schmitt trigger and filter
circuits which suppress noise spikes to assure proper
device operation even on a noisy bus.
READ OPERATION
Current Address Read
Random Read
Sequential Read
Noise Protection
CC
threshold detector circuit
24LC164
DS21093I-page 7
CC