AT24C01A-10SI Atmel, AT24C01A-10SI Datasheet
AT24C01A-10SI
Specifications of AT24C01A-10SI
Available stocks
Related parts for AT24C01A-10SI
AT24C01A-10SI Summary of contents
Page 1
... The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24C01A/02/04/08/16 is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead MAP, 5-lead SOT23 (AT24C01A/AT24C02/AT24C04), 8- lead TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wire serial inter- face ...
Page 2
... Voltage on Any Pin with Respect to Ground .................................... –1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V DC Output Current........................................................ 5.0 mA Figure 1. Block Diagram AT24C01A/02/04/08/16 2 *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and ...
Page 3
... DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hard wired for the AT24C01A and the AT24C02. As many as eight 1K/2K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). ...
Page 4
... Input High Level IH V Output Low Level V = 3.0V OL2 CC V Output Low Level V = 1.8V OL1 CC Note min and V max are reference only and are not tested AT24C01A/02/04/08/ 25° 1.0 MHz SCL 40°C to +85°C, V – AI Test Condition READ at 100 kHz WRITE at 100 kHz ...
Page 5
... The 24C01A/02/04 bearing the process letter “D” on the package (the mark is located in the lower right corner on the top side of the package), guarantees 400 kHz (2.5 – 5.0V). 2. This parameter is characterized and is not 100% tested. 0180T–SEEPR–12/04 = 40°C to +85°C, V – AI (1) (1) AT24C01A/02/04/08/16 = +1.8V to +5.5V +2.7V to +5.5V 1.8-volt 2.5, 2.7, 5.0-volt Min Max Min ...
Page 6
... EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C01A/02/04/08/16 features a low-power standby mode which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the completion of any internal operations ...
Page 7
... Figure 3. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: 1. The write cycle time t is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. WR Figure 4. Data Validity 0180T–SEEPR–12/04 ACK t wr STOP CONDITION AT24C01A/02/04/08/16 (1) START CONDITION 7 ...
Page 8
... Figure 5. Start and Stop Definition Figure 6. Output Acknowledge AT24C01A/02/04/08/16 8 0180T–SEEPR–12/04 ...
Page 9
... If more than eight (1K/2K) or sixteen (4K, 8K, 16K) data words are transmitted to the EEPROM, the data word address will “roll over” and previ- ous data will be overwritten. AT24C01A/02/04/08/ the 9 ...
Page 10
... The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (see Figure 12 on page 12). AT24C01A/02/04/08/16 10 0180T–SEEPR–12/04 ...
Page 11
... Figure 7. Device Address Notes: Figure 8. Byte Write Figure 9. Page Write (* = DON’T CARE bit for 1K) 0180T–SEEPR–12/04 (1) 8K (2) 16K 1. This device is not recommended for new designs. Please refer to AT24C08A. 2. This device is not recommended for new designs. Please refer to AT24C16A. AT24C01A/02/04/08/16 11 ...
Page 12
... Figure 10. Current Address Read Figure 11. Random Read (* = DON’T CARE bit for 1K) Figure 12. Sequential Read AT24C01A/02/04/08/16 12 0180T–SEEPR–12/04 ...
Page 13
... AT24C01A Ordering Information Ordering Code AT24C01A-10PI-2.7 AT24C01A-10SI-2.7 AT24C01A-10TI-2.7 AT24C01A-10PI-1.8 AT24C01A-10SI-1.8 AT24C01A-10TI-1.8 AT24C01A-10PU-2.7 AT24C01A-10PU-1.8 AT24C01A-10SU-2.7 AT24C01A-10SU-1.8 AT24C01A-10TU-2.7 AT24C01A-10TU-1.8 AT24C01A-10TSU-2.7 AT24C01A-10TSU-1.8 AT24C01AU3-10UU-2.7 AT24C01AU3-10UU-1.8 AT24C01AY1-10YU-2.7 AT24C01AY1-10YU-1.8 (2) AT24C01A-W2.7-11 (2) AT24C01A-W1.8-11 Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. ...
Page 14
... Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) 5TS1 5-lead, 2. 1.60 mm Body, Plastic Thin Shrink Small Outline Package (SOT23) 8U3-1 8-ball, die Ball Grid Away Package (dBGA2) –2.7 Low-voltage (2.7V to 5.5V) –1.8 Low-voltage (1.8V to 5.5V) AT24C01A/02/04/08/16 14 (1) Package 8P3 8S1 8A2 8P3 8S1 ...
Page 15
... Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) 5TS1 5-lead, 2. 1.60 mm Body, Plastic Thin Shrink Small Outline Package (SOT23) 8U3-1 8-ball, die Ball Grid Away Package (dBGA2) –2.7 Low-voltage (2.7V to 5.5V) –1.8 Low-voltage (1.8V to 5.5V) 0180T–SEEPR–12/04 AT24C01A/02/04/08/16 (1) Package 8P3 8S1 8A2 8P3 8S1 8A2 8P3 ...
Page 16
... Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) –2.7 Low-voltage (2.7V to 5.5V) –1.8 Low-voltage (1.8V to 5.5V) AT24C01A/02/04/08/16 16 Package 8P3 8S1 8A2 8P3 8S1 8A2 ...
Page 17
... Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) –2.7 Low-voltage (2.7V to 5.5V) –1.8 Low-voltage (1.8V to 5.5V) 0180T–SEEPR–12/04 AT24C01A/02/04/08/16 Package 8P3 8S1 8A2 8P3 8S1 8A2 Package Type ...
Page 18
... D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 2325 Orchard Parkway San Jose, CA 95131 R AT24C01A/02/04/08/ ...
Page 19
... These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 0180T–SEEPR–12/ Top View TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) AT24C01A/02/04/08/ ∅ End View COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM A 1.35 – 1. ...
Page 20
... Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and determined at Datum Plane H. 2325 Orchard Parkway San Jose, CA 95131 R AT24C01A/02/04/08/ TITLE 8A2, 8-lead, 4 ...
Page 21
... Top View Side View 2325 Orchard Parkway San Jose, CA 95131 R 0180T–SEEPR–12/ End View A SYMBOL TITLE 8Y1, 8-lead (4.90 x 3.00 mm Body) MSOP Array Package (MAP) Y1 AT24C01A/02/04/08/ PIN 1 INDEX AREA Bottom View COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX NOM NOTE – ...
Page 22
... The Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and an adjacent lead shall not be less than 0.07 mm. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R AT24C01A/02/04/08/ Top View ...
Page 23
... This drawing is for general information only. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 0180T–SEEPR–12/ TITLE 8U3-1, 8-ball, 1.50 x 2.00 mm Body, 0.50 mm pitch, Small Die Ball Grid Array Package (dBGA2) AT24C01A/02/04/08/ Side View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A 0 ...
Page 24
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...