AT24C01A-10SI-2.7 Atmel, AT24C01A-10SI-2.7 Datasheet

Page 1

... The AT24C01A/02/04/08A/16A is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin Mini-MAP (MLP 2x3) (AT24C01A/AT24C02/AT24C04), 8-lead TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wire serial interface. In addition, the entire family is available in 2.7V (2.7V to 5.5V) and 1.8V (1.8V to 5.5V) versions. ...

Page 2

... Voltage on Any Pin with Respect to Ground .................................... –1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V DC Output Current........................................................ 5.0 mA Figure 1. Block Diagram AT24C01A/02/04/08A/16A 2 *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and ...

Page 3

... DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hard wired for the AT24C01A and the AT24C02. As many as eight 1K/2K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). ...

Page 4

... IH V Output Low Level V = 3.0V OL2 CC V Output Low Level V = 1.8V OL1 CC Note min and V max are reference only and are not tested AT24C01A/02/04/08A/16A 4 = 25° 1.0 MHz SCL 40°C to +85°C, V – AI Test Condition READ at 100 kHz WRITE at 100 kHz ...

Page 5

Table 5. AC Characteristics Applicable over recommended operating range from TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter f Clock Frequency, SCL SCL t Clock Pulse Width Low LOW t Clock Pulse Width High ...

Page 6

... EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C01A/02/04/08A/16A features a low-power standby mode which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the completion of any internal operations ...

Page 7

Bus Timing Figure 2. SCL: Serial Clock, SDA: Serial Data I/O Write Cycle Timing Figure 3. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: 1. The write cycle time t is the time from a ...

Page 8

... Figure 5. Start and Stop Definition Figure 6. Output Acknowledge AT24C01A/02/04/08A/16A 8 0180Z1–SEEPR–5/07 ...

Page 9

... At this time the EEPROM enters an internally timed write cycle, t nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 8 on page 11). ...

Page 10

... The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (see Figure 12 on page 12). AT24C01A/02/04/08A/16A 10 0180Z1–SEEPR–5/07 ...

Page 11

Figure 7. Device Address Figure 8. Byte Write Figure 9. Page Write (* = DON’T CARE bit for 1K) 0180Z1–SEEPR–5/07 MSB 8K 16K 11 ...

Page 12

... Figure 10. Current Address Read Figure 11. Random Read (* = DON’T CARE bit for 1K) Figure 12. Sequential Read AT24C01A/02/04/08A/16A 12 0180Z1–SEEPR–5/07 ...

Page 13

... AT24C01A Ordering Information Ordering Code (2) AT24C01A-10PU-2.7 (2) AT24C01A-10PU-1.8 (2) AT24C01A-10SU-2.7 (2) AT24C01A-10SU-1.8 (2) AT24C01A-10TU-2.7 (2) AT24C01A-10TU-1.8 (2) AT24C01A-10TSU-1.8 (2) AT24C01AU3-10UU-1.8 (2) AT24C01AY1-10YU-1.8 (Not recommended for new design) (3) AT24C01AY6-10YH-1.8 (4) AT24C01A-W1.8-11 Notes: 1. This device is not recommended for new design. Please refer to AT24C01B datasheet. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. ...

Page 14

... Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) 5TS1 5-lead, 2. 1.60 mm Body, Plastic Thin Shrink Small Outline Package (SOT23) 8U3-1 8-ball, die Ball Grid Away Package (dBGA2) –2.7 Low-voltage (2.7V to 5.5V) –1.8 Low-voltage (1.8V to 5.5V) AT24C01A/02/04/08A/16A 14 (1) Package 8P3 8P3 8S1 8S1 8A2 ...

Page 15

AT24C04 Ordering Information Ordering Code (2) AT24C04-10PU-2.7 (2) AT24C04-10PU-1.8 (2) AT24C04N-10SU-2.7 (2) AT24C04N-10SU-1.8 (2) AT24C04-10TU-2.7 (2) AT24C04-10TU-1.8 (2) AT24C04Y1-10YU-1.8 (Not recommended for new design) (3) AT24C04Y6-10YH-1.8 (2) AT24C04-10TSU-1.8 (2) AT24C04U3-10UU-1.8 (4) AT24C04-W1.8-11 Notes: 1. For 2.7V devices used in the ...

Page 16

... Body, 0.50 mm Pitch, Ultra Thin Mini-MAP, Dual No Lead Package (DFN), (MLP 2x3 mm) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) −2.7 Low Voltage (2.7V to 5.5V) −1.8 Low Voltage (1.8V to 5.5V) AT24C01A/02/04/08A/16A 16 (1) Package 8P3 8P3 8S1 8S1 ...

Page 17

AT24C16A Ordering Information Ordering Code (2) AT24C16A-10PU-2.7 (2) AT24C16A-10PU-1.8 (2) AT24C16AN-10SU-2.7 (2) AT24C16AN-10SU-1.8 (2) AT24C16A-10TU-2.7 (2) AT24C16A-10TU-1.8 (2) AT24C16AY1-10YU-1.8 (Not recommended for new design) (3) AT24C16AY6-10YH-1.8 (2) AT24C16AU2-10UU-1.8 (3) AT24C16A-W1.8-11 Notes: 1. This device is not recommended for new design. ...

Page 18

... D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 2325 Orchard Parkway San Jose, CA 95131 R AT24C01A/02/04/08A/16A ...

Page 19

JEDEC SOIC e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 0180Z1–SEEPR–5/07 1 ...

Page 20

... Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and determined at Datum Plane H. 2325 Orchard Parkway San Jose, CA 95131 R AT24C01A/02/04/08A/16A TITLE 8A2, 8-lead, 4 ...

Page 21

MAP D E Top View Side View 2325 Orchard Parkway San Jose, CA 95131 R 0180Z1–SEEPR–5/ End View A SYMBOL TITLE 8Y1, 8-lead (4.90 x 3.00 mm ...

Page 22

... Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 2325 Orchard Parkway San Jose, CA 95131 R AT24C01A/02/04/08A/16A 22 A Pin 1 Index ...

Page 23

SOT23 E1 1 Seating Plane NOTES: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB, for additional information. 2. Dimension D does not include mold flash, protrusions, or gate burrs. Mold flash, ...

Page 24

... Pin 1 Mark this corner D Top View Bottom View Notes: 1. These drawings are for general information only. No JEDEC Drawing to refer to for additional information. 2. Dimension is measured at the maximum solder ball diameter, parallel to primary datum Z. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R AT24C01A/02/04/08A/16A Øb SYMBOL ...

Page 25

PIN 1 BALL PAD CORNER Top View PIN 1 BALL PAD CORNER 1 2 (d1 (e1) Bottom View 8 SOLDER BALLS 1. Dimension “b” is measured at the maximum solder ball diameter. This ...

Page 26

... Revision History Doc. No. 0180Z1 AT24C01A/02/04/08A/16A 26 Date Comments 5/2007 Implemented revision history. Changed formatting on page 16 0180Z1–SEEPR–5/07 ...

Page 27

... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...