AT25128-10PC Atmel, AT25128-10PC Datasheet - Page 8
![IC EEPROM 128KBIT 3MHZ 8DIP](/photos/6/50/65033/313-8-dip_sml.jpg)
AT25128-10PC
Manufacturer Part Number
AT25128-10PC
Description
IC EEPROM 128KBIT 3MHZ 8DIP
Manufacturer
Atmel
Datasheet
1.AT25128-10PC.pdf
(22 pages)
Specifications of AT25128-10PC
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
128K (16K x 8)
Speed
3MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT25128-10PC
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
8
AT25128/256
The WRSR instruction also allows the user to enable or disable the write protect (WP)
pin through the use of the Write Protect Enable (WPEN) bit. Hardware write protection is
enabled when the WP pin is low and the WPEN bit is “1”. Hardware write protection is
disabled when either the WP pin is high or the WPEN bit is “0.” When the device is hard-
ware write protected, writes to the Status Register, including the Block Protect bits and
the WPEN bit, and the block-protected sections in the memory array are disabled.
Writes are only allowed to sections of the memory which are not block-protected.
NOTE: When the WPEN bit is hardware write protected, it cannot be changed back to
“0”, as long as the WP pin is held low.
Table 9. WPEN Operation
READ SEQUENCE (READ): Reading the AT25128/256 via the SO pin requires the
following sequence. After the CS line is pulled low to select a device, the READ op-code
is transmitted via the SI line followed by the byte address to be read (see Table 10 on
page 9). Upon completion, any data on the SI line will be ignored. The data (D7
the specified address is then shifted out onto the SO line. If only one byte is to be read,
the CS line should be driven high after the data comes out. The read sequence can be
continued since the byte address is automatically incremented and data will continue to
be shifted out. When the highest address is reached, the address counter will roll over to
the lowest address allowing the entire memory to be read in one continuous read cycle.
WRITE SEQUENCE (WRITE): In order to program the AT25128/256, two separate
instructions must be executed. First, the device must be write enabled via the WREN
instruction. Then a Write instruction may be executed. Also, the address of the memory
location(s) to be programmed must be outside the protected address field location
selected by the block write protection level. During an internal write cycle, all commands
will be ignored except the RDSR instruction.
A Write instruction requires the following sequence. After the CS line is pulled low to
select the device, the Write op-code is transmitted via the SI line followed by the byte
address and the data (D7
ming will start after the CS pin is brought high. The low-to-high transition of the CS pin
must occur during the SCK low time immediately after clocking in the D0 (LSB) data bit.
The Ready/Busy status of the device can be determined by initiating a Read Status
Register (RDSR) instruction. If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”,
the write cycle has ended. Only the RDSR instruction is enabled during the write pro-
gramming cycle.
WPEN
0
0
1
1
X
X
High
High
Low
Low
WP
X
X
WEN
–
0
1
0
1
0
1
D0) to be programmed (see Table 10 on page 9). Program-
Protected
Protected
Protected
Protected
Protected
Protected
Protected
Blocks
Unprotected
Protected
Protected
Protected
Writable
Writable
Writable
Blocks
0872O–SEEPR–03/05
Protected
Protected
Protected
Protected
Register
Writable
Writable
Status
–
D0) at