AT29LV040A-15JI Atmel, AT29LV040A-15JI Datasheet
AT29LV040A-15JI
Specifications of AT29LV040A-15JI
Available stocks
Related parts for AT29LV040A-15JI
AT29LV040A-15JI Summary of contents
Page 1
... Green (Pb/Halide-free) Packaging Option 1. Description The AT29LV040A is a 3-volt only in-system Flash Programmable and Erasable Read Only Memory (PEROM). Its 4 megabits of memory is organized as 524,288 words by 8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS EEPROM technology, the device offers access times to 150 ns, and a low 54 mW power dissipation. When the device is deselected, the CMOS standby current is less than 50 ...
Page 2
... Pin Configurations Pin Name A0 - A18 I/O0 - I/O7 NC 2.1 32-lead PLCC Top View 2.2 32-lead TSOP (Type 1) Top View AT29LV040A 2 Function Addresses Chip Enable Output Enable Write Enable Data Inputs/Outputs No Connect I/ A11 A13 4 A14 5 A17 VCC 8 A18 9 A16 10 A15 11 A12 A14 A13 ...
Page 3
... Device Operation 4.1 Read The AT29LV040A is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever high. This dual-line con- trol gives designers flexibility in preventing bus contention ...
Page 4
... DATA Polling The AT29LV040A features DATA polling to indicate the end of a program cycle. During a pro- gram cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin ...
Page 5
... These two 16K memory sections are referred to as boot blocks. Secure code which will bring up a system can be contained in a boot block. The AT29LV040A blocks are located in the first 16K bytes of memory and the last 16K bytes of memory. The boot block programming lockout feature can therefore support systems that boot from the lower addresses of memory or the higher addresses ...
Page 6
... IL ( A18 = A18 = V Condition MHz mA 3.6V OUT 1 -100 3. AT29LV040A-15 -40°C - 85°C 3.3V 0. OUT High Z High Z ( Manufacturer Code ( Device Code Manufacturer Code Device Code IH Min Max 0.6 2.0 .45 2.4 0334H–FLASH–9/08 (4) (4) (4) (4) Units A ...
Page 7
... ACC specified from whichever occurs first ( pF This parameter is characterized and is not 100% tested. 0334H–FLASH–9/08 (1)(2)(3)( after the address transition without impact on t ACC after the falling edge of CE without impact AT29LV040A AT29LV040A-15 Min Max Units 150 ns 150 ACC ...
Page 8
... Input Test Waveforms and Measurement Level t R 12. Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. These parameters are characterized and not 100% tested. AT29LV040A < Max 6 12 Units Conditions OUT 0334H–FLASH–9/08 ...
Page 9
... CE Controlled Notes: 1. The 3-byte address and data commands shown on the next page must be applied prior to byte loads complete sector (256 bytes) should be loaded using these waveforms shown in these byte load waveform diagrams. 0334H–FLASH–9/08 (1)(2) AT29LV040A Min Max Units 10 100 ...
Page 10
... LOAD DATA A0 TO ADDRESS 5555 WRITES ENABLED LOAD DATA TO ENTER DATA (3) SECTOR (256 BYTES) PROTECT STATE AT29LV040A 10 (1) Notes: 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Data Protect state will be re-activated at end of program cycle. 3. 256 bytes of data MUST BE loaded. (2) ...
Page 11
... Toggling Bit Waveforms Notes: 1. Toggling either both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used by the address should not vary. 0334H–FLASH–9/08 (1) (1) (1)(3) AT29LV040A Min Typ Max Min Typ Max ...
Page 12
... The device returns to standard operation mode. 5. Manufacturer Code is 1F. The Device Code is C4. 0334H–FLASH–9/08 25. Boot Block Lockout Feature Enable Algorithm (2)(3)(5) Notes: ( AT29LV040A LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 80 TO ADDRESS 5555 LOAD DATA AA TO ...
Page 13
... Green Package Option (Pb/Halide-free) I (mA ACC (ns) Active Standby 150 15 0.05 32J 32-lead, Plastic J-leaded Chip Carrier (PLCC) 32T 32-lead, Thin Small Outline Package (TSOP) 0334H–FLASH–9/08 Ordering Code Package AT29LV040A-15JU 32J AT29LV040A-15TU 32T Package Type AT29LV040A Operation Range Industrial (-40 to 85C) 13 ...
Page 14
... Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010 (0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004 (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT29LV040A 14 1.14(0.045 PIN NO. 1 IDENTIFIER ...
Page 15
... Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0334H–FLASH–9/08 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT29LV040A 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – ...
Page 16
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...