AT45DB081D-SSU Atmel, AT45DB081D-SSU Datasheet - Page 8
![IC FLASH 8MBIT 66MHZ 8SOIC](/photos/6/50/65032/453-8-soic_sml.jpg)
AT45DB081D-SSU
Manufacturer Part Number
AT45DB081D-SSU
Description
IC FLASH 8MBIT 66MHZ 8SOIC
Manufacturer
Atmel
Datasheet
1.AT45DB081D-MU.pdf
(53 pages)
Specifications of AT45DB081D-SSU
Format - Memory
FLASH
Memory Type
DataFLASH
Memory Size
8M (4096 pages x 264 bytes)
Speed
66MHz
Interface
SPI, RapidS
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Density
8Mb
Access Time (max)
6ns
Interface Type
Serial (SPI)
Boot Type
Not Required
Address Bus
1b
Operating Supply Voltage (typ)
3/3.3V
Operating Temp Range
-40C to 85C
Package Type
SOIC EIAJ
Program/erase Volt (typ)
2.7 to 3.6V
Sync/async
Synchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Supply Current
15mA
Mounting
Surface Mount
Pin Count
8
Architecture
Sectored
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.7 V
Maximum Operating Current
15 mA
Mounting Style
SMD/SMT
Organization
64 KB x 16
Ic Interface Type
Serial, SPI
Clock Frequency
50MHz
Supply Voltage Range
2.7V To 3.6V
Memory Case Style
SOIC
No. Of Pins
8
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT45DB081D-SSU
Manufacturer:
Atmel
Quantity:
28 200
Part Number:
AT45DB081D-SSU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT45DB081D-SSU-2.5
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
7. Program and Erase Commands
7.1
7.2
7.3
8
Buffer Write
Buffer to Main Memory Page Program with Built-in Erase
Buffer to Main Memory Page Program without Built-in Erase
Atmel AT45DB081D
Data can be clocked in from the input pin (SI) into either buffer 1 or buffer 2. To load data into the
standard Atmel
fer 2, must be clocked into the device, followed by three address bytes comprised of 15 don’t
care bits and nine buffer address bits (BFA8 - BFA0). The nine buffer address bits specify the
first byte in the buffer to be written. To load data into the binary buffers (256-bytes each), a 1-
byte opcode 84H for buffer 1 or 87H for buffer 2, must be clocked into the device, followed by
three address bytes comprised of 16 don’t care bits and eight buffer address bits (BFA7 - BFA0).
The eight buffer address bits specify the first byte in the buffer to be written. After the last
address byte has been clocked into the device, data can then be clocked in on subsequent clock
cycles. If the end of the data buffer is reached, the device will wrap around back to the beginning
of the buffer. Data will continue to be loaded into the buffer until a low-to-high transition is
detected on the CS pin.
Data written into either buffer 1 or buffer 2 can be programmed into the main memory. A 1-byte
opcode, 83H for buffer 1 or 86H for buffer 2, must be clocked into the device. For the DataFlash
standard page size (264-bytes), the opcode must be followed by three address bytes consist of
three don’t care bits, 12 page address bits (PA11 - PA0) that specify the page in the main mem-
ory to be written and nine don’t care bits. To perform a buffer to main memory page program
with built-in erase for the binary page size (256-bytes), the opcode 83H for buffer 1 or 86H for
buffer 2, must be clocked into the device followed by three address bytes consisting of four don’t
care bits 12 page address bits (A19 - A8) that specify the page in the main memory to be written
and eight don’t care bits. When a low-to-high transition occurs on the CS pin, the part will first
erase the selected page in main memory (the erased state is a logic 1) and then program the
data stored in the buffer into the specified page in main memory. Both the erase and the pro-
gramming of the page are internally self-timed and should take place in a maximum time of t
During this time, the status register will indicate that the part is busy.
A previously-erased page within main memory can be programmed with the contents of either
buffer 1 or buffer 2. A 1-byte opcode, 88H for buffer 1 or 89H for buffer 2, must be clocked into
the device. For the DataFlash standard page size (264-bytes), the opcode must be followed by
three address bytes consist of three don’t care bits, 12 page address bits (PA11 - PA0) that
specify the page in the main memory to be written and nine don’t care bits. To perform a buffer
to main memory page program without built-in erase for the binary page size (256-bytes), the
opcode 88H for buffer 1 or 89H for buffer 2, must be clocked into the device followed by three
address bytes consisting of four don’t care bits, 12 page address bits (A19 - A8) that specify the
page in the main memory to be written and eight don’t care bits. When a low-to-high transition
occurs on the CS pin, the part will program the data stored in the buffer into the specified page in
the main memory. It is necessary that the page in main memory that is being programmed has
been previously erased using one of the erase commands (Page Erase or Block Erase). The
programming of the page is internally self-timed and should take place in a maximum time of t
During this time, the status register will indicate that the part is busy.
®
DataFlash
®
buffer (264-bytes), a 1-byte opcode, 84H for buffer 1 or 87H for buf-
3596M–DFLASH–5/10
EP
P
.
.