AT25DF321-SU Atmel, AT25DF321-SU Datasheet - Page 14

• Manufacturer Part Number: AT25DF321-SU
• Description: IC FLASH 32MBIT 70MHZ 8SOIC
• Manufacturer: Atmel

Specifications of AT25DF321-SU

• Format - Memory: FLASH
• Memory Type: DataFLASH
• Memory Size: 32M (16384 pages x 256 Bytes)
• Speed: 70MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.4
14
Unprotect Sector
AT25DF321
A0 will be set to the logical “1” state, and the sector itself will then be protected from program
and erase operations. In addition, the WEL bit in the Status Register will be reset back to the log-
ical “0” state.
The complete three address bytes must be clocked into the device before the CS pin is deas-
serted, and the CS pin must be deasserted on an even byte boundary (multiples of eight bits);
otherwise, the device will abort the operation, the state of the Sector Protection Register will be
unchanged, and the WEL bit in the Status Register will be reset to a logical “0”.
As a safeguard against accidental or erroneous protecting or unprotecting of sectors, the Sector
Protection Registers can themselves be locked from updates by using the SPRL (Sector Protec-
tion Registers Locked) bit of the Status Register (please refer to
on page 20
issue the Protect Sector command will be ignored, and the device will reset the WEL bit in the
Status Register back to a logical “0” and return to the idle state once the CS pin has been
deasserted.
Figure 9-3.
Issuing the Unprotect Sector command to a particular sector address will reset the correspond-
ing Sector Protection Register to the logical “0” state (see
Protection Register values). Every physical sector of the device has a corresponding single-bit
Sector Protection Register that is used to control the software protection of a sector.
Before the Unprotect Sector command can be issued, the Write Enable command must have
been previously issued to set the WEL bit in the Status Register to a logical “1”. To issue the
Unprotect Sector command, the CS pin must first be asserted and the opcode of 39h must be
clocked into the device. After the opcode has been clocked in, the three address bytes designat-
ing any address within the sector to be unlocked must be clocked in. Any additional data clocked
into the device after the address bytes will be ignored. When the CS pin is deasserted, the Sec-
tor Protection Register corresponding to the sector addressed by A23-A0 will be reset to the
logical “0” state, and the sector itself will be unprotected. In addition, the WEL bit in the Status
Register will be reset back to the logical “0” state.
The complete three address bytes must be clocked into the device before the CS pin is deas-
serted, and the CS pin must be deasserted on an even byte boundary (multiples of eight bits);
otherwise, the device will abort the operation, the state of the Sector Protection Register will be
unchanged, and the WEL bit in the Status Register will be reset to a logical “0”.
SCK
CS
SO
SI
for more details). If the Sector Protection Registers are locked, then any attempts to
Protect Sector
MSB
HIGH-IMPEDANCE
0
0
0
1
1
2
OPCODE
1
3
0
4
1
5
1
6
0
7
MSB
A
8
A
9
A
10 11
A
ADDRESS BITS A23-A0
A
12
A
Table 9-1 on page 13
A
26
“Status Register Commands”
A
27 28
A
A
29 30
A
A
31
3669B–DFLASH–6/09
for Sector