MT48LC16M4A2TG-75:G TR Micron Technology Inc, MT48LC16M4A2TG-75:G TR Datasheet - Page 50
![IC SDRAM 64MBIT 133MHZ 54TSOP](/photos/7/22/72261/557-54-tsop_sml.jpg)
MT48LC16M4A2TG-75:G TR
Manufacturer Part Number
MT48LC16M4A2TG-75:G TR
Description
IC SDRAM 64MBIT 133MHZ 54TSOP
Manufacturer
Micron Technology Inc
Datasheet
1.MT48LC4M16A2P-75G_TR.pdf
(72 pages)
Specifications of MT48LC16M4A2TG-75:G TR
Format - Memory
RAM
Memory Type
SDRAM
Memory Size
64M (16Mx4)
Speed
133MHz
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Package / Case
54-TSOP II
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
557-1066-1
MT48LC16M4A2TG-75:G
MT48LC16M4A2TG-75:G
Notes
PDF: 09005aef80725c0b/Source: 09005aef806fc13c
64MSDRAM_2.fm - Rev. N 12/08 EN
10.
11. C timing and I
12. Other input signals are allowed to transition no more than once every two clocks and
13. I
14. Timing actually specified by
15. Timing actually specified by
16. Timing actually specified by
17. Required clocks are specified by JEDEC functionality and are not dependent on any
18. The I
19. Address transitions average one transition every two clocks.
20. CLK must be toggled a minimum of two times during this period.
21. Based on
1. All voltages referenced to V
2. This parameter is sampled. V
3. I
4. Enables on-chip refresh and address counters.
5. The minimum specifications are used only to indicate cycle time at which proper
6. An initial pause of 100µs is required after power-up, followed by two AUTO REFRESH
7. AC characteristics assume
8. In addition to meeting the transition rate specification, the clock and CKE must tran-
9. Outputs measured at 1.5V with equivalent load:
biased at 1.4V.
with minimum cycle time and the outputs open.
operation over the full temperature range (0°C ≤ T
≤ +85°C (industrial), and –40°C ≤ T
commands, before proper device operation is ensured. (V
ered up simultaneously. V
REFRESH command wake-ups should be repeated any time the
ment is exceeded.
sit between V
Q
t
a reference to V
High-Z.
crossover point. If the input transition time is longer than 1 ns, then the timing is ref-
erenced at V
should always be 1.5V referenced to crossover. Refer to Micron technical note
TN-48-09.
are otherwise at valid V
cycle rate.
minimum cycle rate.
timing parameter.
frequency alteration for the test condition.
DD
HZ defines the time at which the output achieves the open circuit condition; it is not
DD
is dependent on output loading and cycle rates. Specified values are obtained
specifications are tested after the device is properly initialized.
DD
current will increase or decrease proportionally according to the amount of
t
CK = 7.5ns for -75 and -7E,
IL
IH
50pF
DD
(MAX) and V
OH
and V
tests have V
or V
IL
OL
IH
(or between V
. The last valid data element will meet
SS
or V
t
50
SS
T = 1ns.
IH
and V
t
t
t
.
DD
CKS; clock(s) specified as a reference only at minimum
WR plus
WR.
IL
(MIN) and no longer at the 1.5V crossover point. CLK
IL
= 0V and V
, V
levels.
SS
A
DD
≤ +105°C (automotive) is ensured.
Q must be at same potential.) The two AUTO
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Q = +3.3V; f = 1 MHz, T
t
IL
t
CK = 6ns for -6.
RP; clock(s) specified as a reference only at
and V
IH
= 3V, with timing referenced to 1.5V
IH
) in a monotonic manner.
A
≤ +70°C (commercial), –40°C ≤ T
64Mb: x4, x8, x16 SDRAM
DD
©2000 Micron Technology, Inc. All rights reserved.
A
and V
= 25°C; pin under test
t
OH before going
t
REF refresh require-
DD
Q must be pow-
Notes
A