TC58128AFTI Toshiba, TC58128AFTI Datasheet
TC58128AFTI
Specifications of TC58128AFTI
TC58128FTI
Available stocks
Related parts for TC58128AFTI
TC58128AFTI Summary of contents
Page 1
... It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property ...
Page 2
... Address register Command register Control HV generator RATING PARAMETER CONDITION OUT TC58128AFT Column buffer Column decoder Data register Sense amp Memory cell array VALUE −0.6 to 4.6 −0.6 to 4.6 −0 0.3 V (≤ 4 0.3 260 −55 to 150 MIN MAX = 0 V 10 2001-05-30 2/33 ...
Page 3
VALID BLOCKS (1) SYMBOL N Number of Valid Blocks VB (1) The TC58128A occasionally contains unusable blocks. Refer to Application Note (14) toward the end of this document. RECOMMENDED DC OPERATING CONDITIONS SYMBOL V Power Supply Voltage CC V High ...
Page 4
... WE High to CE Low WHC t WE High to RE Low WHR t ALE Low to RE Low (ID Read) AR1 t CE Low to RE Low (ID Read Memory Cell Array to Starting Address High to Busy WB t ALE Low to RE Low (Read Cycle) AR2 t RE Last Clock Rising Edge to Busy (in Sequential Read ...
Page 5
Note: (1) CE High to Ready time depends on the pull-up resistor tied to the (Refer to Application Note (9) toward the end of this document.) (2) Sequential Read is terminated when t is less than 30 ns ...
Page 6
TIMING DIAGRAMS Latch Timing Diagram for Command/Address/Data CLE ALE I/O1 to I/O8 Command Input Cycle Timing Diagram CLE t CLS ALS ALE I/O1 to I/O8 Setup Time CLH t ...
Page 7
Address Input Cycle Timing Diagram t CLS CLE ALS ALE I/O1 to I/O8 Data Input Cycle Timing Diagram CLE CE t ALS ALE WE I/ ...
Page 8
Serial Read Cycle Timing Diagram REA I/ Status Read Cycle Timing Diagram CLE t CLS I/O1 to I/O8 RY ...
Page 9
Read Cycle (1) Timing Diagram CLE t t CLS CLH ALH ALS ALE I/O1 00H I/O8 Column address N* RY ...
Page 10
Read Cycle (2) Timing Diagram CLE t t CLS CLH ALH ALE I/O1 01H to I/ Read Operation using 01H Command N: 0 ...
Page 11
Sequential Read (1) Timing Diagram CLE CE WE ALE RE I/O1 00H A16 A17toA23 to I/O8 Column address Sequential Read (2) Timing Diagram CLE CE WE ALE RE I/O1 01H A0 ...
Page 12
Sequential Read (3) Timing Diagram CLE CE WE ALE RE I/O1 50H A16 A17toA23 to I/O8 Column address Page t 512 + 512 + 512 + R address ...
Page 13
Auto-Program Operation Timing Diagram t CLS CLE t t CLS CLH ALH t ALS ALE I/O1 80H ...
Page 14
ID Read Operation Timing Diagram CLE t CLS t CLS ALH ALS ALE I/O1 90H to I/ ALH AR1 ...
Page 15
... PIN FUNCTIONS The device is a serial access memory which utilizes time-sharing input of address information. The device pin-outs are configured as shown in Figure 1. Command Latch Enable: CLE The CLE input signal is used to control loading of the operation mode command into the internal command register. The command is latched into the command register from the I/O port on the rising edge of the WE signal while CLE is High ...
Page 16
... I/O1 A page consists of 528 bytes in which 512 bytes are used for main memory storage and 16 bytes are for redundancy I/O8 or for other uses. 1 page = 528 bytes 32 pages 1 block = 528 bytes × 32 pages = (16K + 512) bytes Capacity = 528 bytes × 32 pages × 1024 blocks ...
Page 17
Table 3. Command table (HEX) First Cycle Serial Data Input 80 Read Mode (1) 00 Read Mode (2) 01 Read Mode (3) 50 Reset FF Auto Program 10 Auto Block Erase 60 Status Read 70 ID Read 90 Once the ...
Page 18
DEVICE OPERATION Read Mode (1) Read mode (1) is set when a 00H command is issued to the Command register. Refer to Figure 3 below for timing details and the block diagram. CLE CE WE ALE ...
Page 19
... Column address 527 on the last page. Busy Addresses bits A0~A3 are used to set the start pointer for the redundant memory cells, while A4~A7 are ignored. 527 Once a 50H command has been issued, the pointer moves to the redundant cell locations and only those 16 cells can be addressed, regardless of the value of the A4-to-A7 address ...
Page 20
Status Read The device automatically implements the execution and verification of the Program and Erase operations. The Status Read function is used to monitor the Ready/Busy status of the device, determine the result (pass/fail Program or Erase operation, ...
Page 21
Auto Page Program The device carries out an Automatic Page Program operation when it receives a “10H” Program command after the address and data have been input. The sequence of command, address and data input is shown below. (Refer to ...
Page 22
Reset The Reset mode stops all operations. For example, in the case of a Program or Erase operation the internally generated voltage is discharged to 0 volts and the device enters Wait state. The response to an “FFH” Reset command ...
Page 23
ID Read The TC58128A contains ID codes which identify the device type and the manufacturer. The ID codes can be read out under the following timing conditions: CLE CE WE ALE RE I/O 90H 00 ID Read command Address 00 ...
Page 24
APPLICATION NOTES AND COMMENTS (1) Power-on/off sequence: The WP signal is useful for protecting against data corruption at power-on/off. The following timing sequence is necessary. The WP signal may be negated any time after the V power up sequence. 2.7 ...
Page 25
Addressing for program operation Within a block, the pages must be programmed consecutively from the LSB (least significant bit) page of the block to MSB (most significant bit) page of the block. Random page address programming is prohibited. From ...
Page 26
Pointer control for “00H”, “01H” and “50H” The device has three Read modes which set the destination of the pointer. Table 7 shows the destination of the pointer, and Figure block diagram of their operations. Table ...
Page 27
termination for the Ready/Busy pin ( A pull-up resistor needs to be used for termination because the circuit Device V SS Figure 21. This data may vary from device to device. ...
Page 28
Note regarding the WP signal The Erase and Program operations are automatically reset when WP goes Low. The operations are enabled and disabled as follows: Enable Programming WE DIN (100 ns min) WW Disable ...
Page 29
When four address cycles are input Although the device may read in a fourth address ignored inside the chip. Read operation CLE CE WE ALE I/O 00H, 01H, 50H Internal read operation starts when ...
Page 30
Several programming cycles on the same page (Partial Page Program) A page can be divided into segments. Each segment can be programmed individually as follows: 1st programming Data Pattern 1 2nd programming All 1s nth programming ...
Page 31
Invalid blocks (bad blocks) The device contains unusable blocks. Therefore, at the time of use, please check whether a block is bad and do not use these bad blocks. Bad Block Bad Block Figure 26. Bad Block Test Flow ...
Page 32
... Block Replacement Program Error occurs Buffer memory Erase When an error occurs in an Erase operation, prevent future accesses to this bad block (again by creating a table within the system or by using another appropriate scheme). DETECTION AND COUNTERMEASURE SEQUENCE Status Read after Erase → Block Replacement Status Read after Program → ...
Page 33
Package Dimensions Weight: 0.53 g (typ.) TC58128AFT 2001-05-30 33/33 ...