LNK562PN Power Integrations, LNK562PN Datasheet - Page 2
![IC OFFLINE SWIT OTP HV 8DIP](/photos/7/32/73217/596-8-bdip_sml.jpg)
LNK562PN
Manufacturer Part Number
LNK562PN
Description
IC OFFLINE SWIT OTP HV 8DIP
Manufacturer
Power Integrations
Series
LinkSwitch®-LPr
Datasheet
1.LNK562PN.pdf
(16 pages)
Specifications of LNK562PN
Output Isolation
Isolated
Frequency Range
61 ~ 71kHz
Voltage - Output
700V
Power (watts)
1.9W
Operating Temperature
-40°C ~ 150°C
Package / Case
8-DIP (0.300", 7.62mm), 7 Leads
Output Voltage
5.8 V
Input / Supply Voltage (max)
265 VAC
Input / Supply Voltage (min)
85 VAC
Duty Cycle (max)
70 %
Switching Frequency
66 KHz
Supply Current
220 uA
Operating Temperature Range
- 40 C to + 150 C
Mounting Style
Through Hole
For Use With
596-1128 - KIT DESIGN REF LINKSWITCH LP596-1104 - DESIGN ACCELERATOR KIT LP SWITCH
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
596-1035-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LNK562PN
Manufacturer:
PowerInt
Quantity:
2 250
Company:
Part Number:
LNK562PN
Manufacturer:
POWER
Quantity:
15 000
Part Number:
LNK562PN
Manufacturer:
POWER
Quantity:
20 000
Rev. H 11/08
Figure 2. Functional Block Diagram.
Pin Functional Description
DRAIN (D) Pin:
The power MOSFET drain connection provides internal
operating current for both startup and steady-state operation.
BYPASS (BP) Pin:
A 0.1 μF external bypass capacitor for the internally generated
5.8 V supply is connected to this pin.
FEEDBACK (FB) Pin:
During normal operation, switching of the power MOSFET is
controlled by this pin. MOSFET switching is disabled when a
current greater than 70 μA fl ows into this pin.
SOURCE (S) Pin:
This pin is the power MOSFET source connection. It is also the
ground reference for the BYPASS and FEEDBACK pins.
LinkSwitch-LP Functional
Description
LinkSwitch-LP comprises a 700 V power MOSFET switch with
a power supply controller on the same die. Unlike conventional
PWM (pulse width modulation) controllers, it uses a simple
ON/OFF control to regulate the output voltage. The controller
consists of an oscillator, feedback (sense and logic) circuit, 5.8
V regulator, BYPASS pin undervoltage circuit, over-temperature
2
OPEN LOOP
PULLDOWN
FEEDBACK
BYPASS
(FB)
(BP)
LNK562-564
0.8 V
1.69 V -V
+
TH
6.3 V
OSCILLATOR
ADJ
JITTER
AUTO-RESTART
RESET
CLOCK
DC
COUNTER
MAX
FAULT
PRESENT
Figure 3. Pin Confi guration.
protection, frequency jittering, current limit circuit, and leading
edge blanking.
Oscillator
The typical oscillator frequency is internally set to an average
of 66/83/100 kHz for the LNK562, 563 & 564 respectively.
Two signals are generated from the oscillator: the maximum
duty cycle signal (DC
the beginning of each switching cycle.
4.85 V
5.8 V
BP
FB
G Package (SMD-8B)
P Package (DIP-8B)
S
S
SHUTDOWN
THERMAL
1
2
3
4
+
-
S
R
Q
Q
BYPASS PIN
UNDER-VOLTAGE
REGULATOR
MAX
8
7
5
5.8 V
) and the clock signal that indicates
S
D
S
CURRENT LIMIT
COMPARATOR
PI-3958-092905
BLANKING
LEADING
EDGE
BP
FB
D
D Package (SO-8C)
+
-
1
2
4
V I
LIMIT
SOURCE
DRAIN
PI-4547-011107
(D)
(S)
8
7
6
5
S
S
S
S