PKS606YN Power Integrations, PKS606YN Datasheet - Page 16

• Manufacturer Part Number: PKS606YN
• Description: IC OFFLINE SWIT OTP OCP HV TO220
• Manufacturer: Power Integrations
• Series: PeakSwitch®r

Specifications of PKS606YN

• Mfg Application Notes: PeakSwitch Design Guide AppNote
• Output Isolation: Isolated
• Frequency Range: 250 ~ 304kHz
• Voltage - Output: 700V
• Power (watts): 117W
• Operating Temperature: -40°C ~ 150°C
• Package / Case: TO-220-7 (Formed Leads), 5 Leads
• Output Voltage: 12 V
• Input / Supply Voltage (max): 265 VAC
• Input / Supply Voltage (min): 85 VAC
• Duty Cycle (max): 65 %
• Switching Frequency: 47 KHz
• Supply Current: 25 uA
• Operating Temperature Range: - 40 C to + 150 C
• Mounting Style: Through Hole
• No. Of Outputs: 1
• Voltage Regulator Case Style: TO-220
• No. Of Pins: 7
• Base Number: 606
• Controller Type: PWM
• Rohs Compliant: Yes
• For Use With: 596-1198 - KIT REF DESIGN 36-72W MOTOR DRVR596-1126 - KIT DESIGN ACC PEAKSWITCH FAMILY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 596-1122-5

NOTES:
A. Total current consumption is the sum of I
B. Since the output MOSFET is switching, it is difficult to isolate the switching current from the supply current at the
C. See Typical Performance Characteristics section for BYPASS pin startup charging waveform.
D. BYPASS pin is externally supplied (bias winding).
E. For current limit at other di/dt values, refer to Figure 25.
F. This parameter is derived from characterization.
G. This parameter is derived from the change in current limit measured at 1X and 4X of the di/dt shown in the I
H. I
I. Breakdown voltage may be checked against minimum BV
J. Auto-restart on time has the same temperature characteristics as the oscillator (inversely proportional to
K. Only applicable if no UV resistor is present at the EN/UV pin. 5 s applies only if the preceding switching auto-
Rev. I 02/07
OUTPUT (cont.)
Auto-Restart
ON Time
Auto-Restart
OFF Time
16
switching) and the sum of I
DRAIN. An alternative is to measure the BYPASS pin current at 6.1 V.
temperature. I
consumption calculations.
to but not exceeding minimum BV
frequency). Auto-restart on time is extended during startup and certain fault conditions because the controller
reduces its oscillator clock frequency to prevent excessive drain currents. If excessive drain currents are still
occuring half way through the auto-restart on time, output MOSFET switching is disabled for the remainder of that
auto-restart on time episode (if the line is not sensed) or the supply latches off (if the line is sensed and adequate
line voltage is present).
restart event did not result in EN/UV pin going low. In that event, the first auto-restart off-time is 150 ms.
specification.
DSS1
Parameter
is the worst case OFF state leakage specification at 80% of BV
PKS603-607
DSS2
is a typical specification under worst case application conditions (rectified 265 VAC) for no-load
Symbol
t
AROFF
t
AR
S2
and I
DSS
DSS
SOURCE = 0 V; T
.
when EN/UV pin is open (MOSFET switching).
(Unless Otherwise Specified)
S1
and I
Conditions
See Figure 18
See Note K
See Note J
T
DSS
J
= 25 °C
when EN/UV pin is shorted to ground (MOSFET not
J
= -40 to 125 °C
DSS
specification by ramping the DRAIN pin voltage up
DSS
and maximum operating junction
Min
Typ
30
5
Max
Units
ms
LIMIT
s