TOP222Y Power Integrations, TOP222Y Datasheet - Page 5
![IC OFFLINE SWIT PWM OCP HV TO220](/photos/28/21/282163/to-220-3_sml.jpg)
TOP222Y
Manufacturer Part Number
TOP222Y
Description
IC OFFLINE SWIT PWM OCP HV TO220
Manufacturer
Power Integrations
Series
TOPSwitch®-IIr
Type
Off Line Switcherr
Datasheet
1.TOP222GN-TL.pdf
(20 pages)
Specifications of TOP222Y
Output Isolation
Isolated
Frequency Range
90 ~ 110kHz
Voltage - Output
700V
Power (watts)
25W
Operating Temperature
-40°C ~ 150°C
Package / Case
TO-220-3
Output Voltage
5.7 V
Input / Supply Voltage (max)
265 VAC
Input / Supply Voltage (min)
85 VAC
Duty Cycle (max)
70 %
Switching Frequency
100 KHz
Supply Current
1.2 mA
Operating Temperature Range
- 40 C to + 150 C
Mounting Style
Through Hole
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TOP222Y
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
TOP222Y-TSTU
Manufacturer:
PowerInte
Quantity:
281
Company:
Part Number:
TOP222YN
Manufacturer:
PI
Quantity:
2 650
Part Number:
TOP222YN
Manufacturer:
POWER
Quantity:
20 000
Figure 6. Typical Waveforms for (1) Normal Operation, (2) Auto-restart, and (3) Power Down Reset.
compensated to minimize variation of the effective peak current
limit due to temperature related changes in output MOSFET
R
The leading edge blanking circuit inhibits the current limit
comparator for a short time after the output MOSFET is turned
on. The leading edge blanking time has been set so that current
spikes caused by primary-side capacitances and secondary-side
rectifier reverse recovery time will not cause premature
termination of the switching pulse.
The current limit can be lower for a short period after the leading
edge blanking time as shown in Figure 12. This is due to
dynamic characteristics of the MOSFET. To avoid triggering
the current limit in normal operation, the drain current waveform
should stay within the envelope shown.
Shutdown/Auto-restart
To minimize TOPSwitch power dissipation, the shutdown/
auto-restart circuit turns the power supply on and off at an auto-
restart duty cycle of typically 5% if an out of regulation
condition persists. Loss of regulation interrupts the external
current into the CONTROL pin. V
shunt mode to the hysteretic auto-restart mode described above.
When the fault condition is removed, the power supply output
DS(ON)
DRAIN
V OUT
I OUT
.
V IN
V C
I C
V IN
0
0
0
0
0
1
C
1
1
regulation changes from
2
2
8
8
1
1
2
2
2
becomes regulated, V
normal operation of the power supply resumes.
Overtemperature Protection
Temperature protection is provided by a precision analog
circuit that turns the output MOSFET off when the junction
temperature exceeds the thermal shutdown temperature
(typically 135 C). Activating the power-up reset circuit by
removing and restoring input power or momentarily pulling the
CONTROL pin below the power-up reset threshold resets the
latch and allows TOPSwitch to resume normal power supply
operation. V
5.7 V (typical) sawtooth waveform is present on the CONTROL
pin when the power supply is latched off.
High-voltage Bias Current Source
This current source biases TOPSwitch from the DRAIN pin and
charges the CONTROL pin external capacitance (C
start-up or hysteretic operation. Hysteretic operation occurs
during auto-restart and overtemperature latched shutdown.
The current source is switched on and off with an effective duty
cycle of approximately 35%. This duty cycle is determined by
the ratio of CONTROL pin charge (I
(I
operation when the output MOSFET is switching.
CD1
8
8
and I
1
1
CD2
1
). This current source is turned off during normal
C
is regulated in hysteretic mode and a 4.7 V to
C
regulation returns to shunt mode, and
3
C
) and discharge currents
TOP221-227
V C(reset)
1
PI-2030-042397
7/01
T
D
) during
5