ADP2291ARMZ-R7 Analog Devices Inc, ADP2291ARMZ-R7 Datasheet - Page 16
![IC CHARGER LI-ION 4.2V 8MSOP](/photos/1/38/13894/rm-8_sml.jpg)
ADP2291ARMZ-R7
Manufacturer Part Number
ADP2291ARMZ-R7
Description
IC CHARGER LI-ION 4.2V 8MSOP
Manufacturer
Analog Devices Inc
Datasheet
1.ADP2291ARMZ-R7.pdf
(20 pages)
Specifications of ADP2291ARMZ-R7
Battery Type
Lithium-Ion (Li-Ion)
Function
Charge Management
Voltage - Supply
4.5 V ~ 12 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
Input Voltage
12V
Battery Charge Voltage
4.2V
Charge Current Max
1.5A
Battery Ic Case Style
MSOP
No. Of Pins
8
No. Of Series Cells
1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
ADP2291-EVAL - BOARD EVAL FOR ADP2291LI
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
ADP2291ARMZ-R7
ADP2291ARMZ-R7TR
ADP2291ARMZ-R7TR
ADP2291
PRINTED CIRCUIT BOARD LAYOUT
CONSIDERATIONS
Use the following general guidelines when designing printed
circuit boards:
•
•
•
•
LFSCP LAYOUT CONSIDERATIONS
The LFCSP package has an exposed die paddle on the bottom
that efficiently conducts heat to the PCB. To achieve the
optimum performance from the LFCSP package, give special
consideration to the layout of the PCB. Use the following layout
guidelines for the LFCSP package:
•
•
Keep the output capacitor as close to the BAT and GND
pins as possible.
Keep the input capacitor as close to the IN and GND pins
as possible.
PC board traces with larger cross-sectional areas remove
more heat from the pass transistor. For optimum heat
transfer, specify thick copper and use wide traces.
Use additional copper layers or planes to reduce thermal
resistance. When connecting to other layers, use multiple
vias if possible.
The pad pattern is shown in Figure 27. Follow the pad
dimension closely for reliable solder joints, while
maintaining reasonable clearances to prevent solder
bridging.
The thermal pad of the LFCSP package provides a low
thermal impedance path (approximately 20°C/W) to the
PCB; therefore, a properly designed PCB effectively con-
ducts the heat away from the package. This is achieved by
adding thermal vias to the PCB that provide a thermal path
to the inner or bottom layers.
35µm PLATING
0.50
2× VIAS, 0.250∅
0.30
Figure 27. 3 mm × 3 mm LFCSP Pad Pattern
0.73
(Dimensions in millimeters)
1.40
1.90
3.36
0.90
1.80
2.36
Rev. A | Page 16 of 20
•
•
•
•
•
Table 7. Variables Description
Variable
Name
V
V
V
I
C rate
MAX
X
RS
BAT, EOC
Note that the via diameter is small to prevent the solder
from flowing through the via and leaving voids in the
thermal pad solder joint.
Note also that the thermal pad is attached to the die sub-
strate; therefore, the thermal planes to which the vias
attach the package must be electrically isolated or
connected to GND.
The solder mask opening should be about 120 microns
(4.7 mils) larger than the pad size, resulting in a minimum
of 60 microns (2.4 mils) clearance between the pad and the
solder mask.
The paste mask opening is typically designed to match the
pad size used on the peripheral pads of the LFCSP package.
This should provide a reliable solder joint as long as the
stencil thickness is about 0.125 mm. The paste mask for the
thermal pad needs to be designed for the maximum coverage
to effectively remove the heat from the package. However,
due to the presence of thermal vias and the size of the ther-
mal pad, eliminating voids may not be possible.
The recommended paste mask stencil thickness is
0.125 mm. Use a laser cut stainless steel stencil with
trapezoidal walls.
Use a no-clean, Type 3 solder paste for mounting the
LFCSP package. A nitrogen purge during the reflow
process is recommended.
The package manufacturer recommends that the reflow
temperature not exceed 220°C and the time above liquidus
be less than 75 seconds. Make sure the preheat ramp is
3°C/second or lower. The actual temperature profile
depends on the board’s density and should be determined
by the assembly house.
Description
The voltage on Pin X.
The regulation setpoint for the voltage across the
sense resistor (RS).
The battery voltage at the point charging current is
1/10 the current setpoint.
The charge current corresponding to VRS,
including the effects of ADJ pin voltage.
The charge current (mA) expressed as a multiple of
the nominal battery capacity (mAh). A 900 mAh
capacity battery, charged at a 1/10 C rate, is
equivalent to a 90 mA charge current.