LTC4253CGN#PBF Linear Technology, LTC4253CGN#PBF Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC4253CGN#PBF
Manufacturer Part Number
LTC4253CGN#PBF
Description
IC HOT SWAP CONTRLR -48V 16-SSOP
Manufacturer
Linear Technology
Type
Hot-Swap Controllerr
Datasheet
1.LTC4253CGNPBF.pdf
(34 pages)
Specifications of LTC4253CGN#PBF
Applications
General Purpose
Internal Switch(s)
No
Voltage - Supply
11.2 V ~ 14.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
16-SSOP (0.150", 3.90mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LTC4253/LTC4253A
applicaTions inForMaTion
Resetting a Fault Latch
A latched circuit breaker fault of the LTC4253/LTC4253A
has the benefit of a long cooling time. The latched fault can
be reset by pulsing the RESET pin high until the TIMER pin
is pulled below V
the RESET pulse, SS and GATE ramp up without an initial
timing cycle provided the interlock conditions are satisfied.
Alternative methods of reset include using an external
switch to pulse the UV pin below V
for the LTC4253A) or the V
Pulling the TIMER pin below V
then simultaneously releasing them also achieves a reset.
An initial timing cycle is generated for reset by pulsing the
UV pin or V
for reset by pulsing of the TIMER and SS pins.
Using Reset as an ON/OFF Switch
The asynchronous RESET pin can be used as an ON/OFF
function to cut off supply to the external power modules
or loads controlled by the LTC4253/LTC4253A. Pulling
RESET high will pull GATE, SS, TIMER and SQTIMER
low and the PWRGD signal high. The supply is fully cut
off if the RESET pulse is maintained wide enough to fully
discharge the GATE and SS pins. As long as RESET is
high, GATE, SS, TIMER and SQTIMER are strapped to V
and the supply is cut off. When RESET is released, if the
LTC4253/LTC4253A are in UVLO, UV, OV or V
turn-on is delayed until the interlock conditions are met
before recovering as described in the Operation, Interlock
Conditions section. If not, the GATE pin will ramp up in a
soft start cycle without going through an initial cycle as
in Figure 13c.
Analog Current Limit and Fast Current Limit
In Figure 14a, when SENSE exceeds V
by the analog current limit amplifier loop. When SENSE
drops below V
when a severe fault occurs, SENSE exceeds V
immediately pulls down until the analog current amplifier
establishes control. If the severe fault causes V
V
into the DRAIN pin and is multiplied by 8. This extra cur-
rent is added to the TIMER pull-up current of 200µA. This
28
DRNCL
, the DRAIN pin is clamped at V
IN
pin, while no initial timing cycle is generated
ACL
TMRL
, GATE is allowed to pull up. In Figure 14b,
(1V) as shown in Figure 13b. After
IN
TMRL
pin below (V
ACL
and the SS pin to 0V
UVLO
, GATE is regulated
DRNCL
(V
FCL
LKO
OUT
UV
SENSE
. I
DRN
and GATE
– V
to exceed
– V
> V
UVHST
flows
LKH
CB
EE
).
,
accelerated TIMER current of (200µA + 8 • I
a shorter circuit breaker fault delay. Careful selection of
C
impedance fault condition.
Soft-Start
If the SS pin is not connected, this pin defaults to a linear
voltage ramp, from 0V to 2.2V in about 300µs (0V to 1.4V
in about 200µs for the LTC4253A) at GATE start-up, as
shown in Figure 15a. If a soft-start capacitor, C
nected to this SS pin, the soft-start response is modified
from a linear ramp to an RC response (Equation 6), as
shown in Figure 15b. This feature allows load current to
slowly ramp-up at GATE start-up. Soft-start is initiated at
time point 3 by a TIMER transition from V
(time points 1 and 2), by the OV pin falling below the V
(V
condition or by the RESET pin falling < 0.8V after a Reset
condition. When the SS pin is below 0.2V, the analog cur-
rent limit amplifier keeps GATE low. Above 0.2V, GATE is
released and 50µA ramps up the compensation network
and GATE capacitance at time point 4. Meanwhile, the SS
pin voltage continues to ramp up. When GATE reaches
the MOSFET’s threshold, the MOSFET begins to conduct.
Due to the MOSFET’s high g
reaches the soft-start control value of V
At time point 6, the GATE voltage is controlled by the current
limit amplifier. The soft-start control voltage reaches the
circuit breaker voltage, V
breaker TIMER activates. As the load capacitor nears full
charge, load current begins to decline below V
current limit loop shuts off and GATE releases at time
point 8. At time point 9, SENSE voltage falls below V
and TIMER deactivates.
Large values of C
time-out as V
during the circuit breaker delay. The load capacitor is un-
able to achieve full charge in one GATE start-up cycle. A
more serious side effect of a large C
duration may be exceeded during soft-start into a low
impedance load. A soft-start voltage below V
activate the circuit breaker TIMER.
T
OV
, R
D
– V
and MOSFET helps prevent SOA damage in a low
OVHST
ACL
for the LTC4253A) threshold after an OV
(t) may marginally exceed the V
SS
can cause premature circuit breaker
CB
m
at time point 7 and the circuit
, the MOSFET current quickly
SS
ACL
value is that SOA
(t) (Equation 7).
TMRH
DRN
CB
) produces
ACL
CB
SS
to V
potential
, is con-
will not
(t). The
425353afd
TMRL
OVLO
CB