X9520V20I-AT2 Intersil, X9520V20I-AT2 Datasheet - Page 19

• Manufacturer Part Number: X9520V20I-AT2
• Description: IC VOLT MON DUAL 2KBIT 20-TSSOP
• Manufacturer: Intersil
• Type: Laser Diode Controller (Fiber Optic)r

Specifications of X9520V20I-AT2

• Number Of Channels: 3
• Voltage - Supply: 2.7 V ~ 5.5 V
• Current - Supply: 1.5mA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-TSSOP
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Absolute Maximum Ratings
Temperature under Bias. . . . . . . . . . . . . . . . . . . . . . . .-65 to +135°C
Voltage on WP pin (With respect to Vss) . . . . . . . . . . . . -1.0 to +15V
Voltage on other pins (With respect to Vss). . . . . . . . . . . -1.0 to +7V
| Voltage on RHx– Voltage on RLx |
DC Output Current (SDA,V1RO,V2RO,V3RO) . . . . . . . . . . . . . 5mA
Supply Voltage Limits
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
DC Electrical Specifications
NOTES:
I
I
I
I
I
V
V
V
V
V
I
V
V
V
CC1
CC2
LI
ai
LO
Vx
1. The device enters the Active state after any START, and remains active until: 9 clock cycles later if the Device Select Bits in the Slave Address
2. The device goes into Standby: 200ns after any STOP, except those that initiate a high voltage write cycle; t
3. Current through external pull up resistor not included.
4.
5.
6. See Ordering Information Table.
7. V
TRIP1PR
TRIPxPR
TRIP1
TRIP2
TRIP3
IL
IH
OLx
(x = 0,1,2. Referenced to Vss) . . . . . . . . . . . . . . . . . . . . . V1/VCC
(Applied V1/VCC voltage, referenced to Vss) . . . . . . . 2.7 to 5.5V
SYMBOL
V
V
(7)
Byte are incorrect; 200ns after a STOP ending a read operation; or t
voltage cycle; or 9 clock cycles after any START that is not followed by the correct Device Select Bits in the Slave Address Byte.
(7)
(2)
(1)
IL
IN = Voltage applied to input pin.
OUT = Voltage applied to output pin.
Min. and V
(6)
(6)
(6)
Current into V
(X9520: Active)
Read memory array
Write nonvolatile memory
Current into V
(X9520:Standby)
With 2-Wire bus activity
No 2-Wire bus activity
Input Leakage Current (SCL, SDA, MR) V
Input Leakage Current (WP)
Analog Input Leakage
Output Leakage Current (SDA, V1RO,
V2RO, V3RO)
V
V
Pre - programmed V
Pre - programmed V
Pre - programmed V
V2 Input leakage current
V3 Input leakage current
Input LOW Voltage (SCL, SDA, WP, MR)
Input HIGH Voltage (SCL,SDA, WP, MR)
V1RO, V2RO, V3RO, SDA Output Low
Voltage
TRIP1
TRIPx
IH
Max. are for reference only and are not tested.
Programming Range
Programming Range (x = 2,3)
PARAMETER
CC
CC
19
Pin
Pin
TRIP1
TRIP2
TRIP3
(3)
(3)
threshold
threshold
threshold
f
V
MR = Vss
WP = Vss or Open/Floating
V
V
V
(2)
Factory shipped default option A
Factory shipped default option B
Factory shipped default option A
Factory shipped default option B
Factory shipped default option A
Factory shipped default option B
V
Others = GND or V
I
SCL
SINK
SDA
SCL
IN
IN
OUT
SDA
(4)
= V
= 400kHz
= V
= 2.0mA
= V
= V
(5)
= GND to V
SS
CC
= GND to V
SCL
CC
to V
X9520
(when no bus activity else f
TEST CONDITIONS/NOTES
= V
CC
WC
CC
with all other analog inputs floating
CC.
CC
after a STOP ending a write operation.
CC.
Thermal Information
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
Recommended Operating Conditions
Industrial Temperature Range . . . . . . . . . . . . . . . . . .-40°C to +85°C
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
X9520 is in Standby
SCL
= 400kHz)
WC
after a STOP that initiates a high
2.75
2.85
4.55
1.65
2.85
1.65
2.85
MIN
-0.5
1.8
2.0
TYP
0.1
0.1
3.0
4.7
1.8
3.0
1.8
3.0
1
V
CC
MAX
4.70
4.70
3.05
4.75
1.85
3.05
1.85
3.05
0.4
1.5
0.8
0.4
August 20, 2007
50
50
10
10
10
10
1
1
+0.5
FN8206.2
UNIT
mA
μA
μA
μA
µA
μA
μA
V
V
V
V
V
V
V
V