X9530V14IT2 Intersil, X9530V14IT2 Datasheet - Page 22

• Manufacturer Part Number: X9530V14IT2
• Description: IC LASER DIODE CTRLR 14-TSSOP
• Manufacturer: Intersil
• Type: Laser Diode Controller (Fiber Optic)r

Specifications of X9530V14IT2

• Number Of Channels: 1
• Voltage - Supply: 3 V ~ 5.5 V
• Current - Supply: 9mA
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 14-TSSOP
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

ABSOLUTE MAXIMUM RATINGS
All voltages are referred to Vss.
Temperature under bias ................... -65°C to +100°C
Storage temperature ........................ -65°C to +150°C
Voltage on every pin except Vcc
Voltage on Vcc Pin .............................................0 to 5.5V
D.C. Output Current at pin SDA
D.C. Output Current at pins R1, R2,
D.C. Output Current at pins I1 and I2 ............... -3 to 3mA
Lead temperature (soldering, 10s) .................... 300°C
OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS
All typical values are for 25°C ambient temperature and 5 V at pin Vcc. Maximum and minimum specifications are
over the recommended operating conditions. All voltages are referred to the voltage at pin Vss unless otherwise
specified. All bits in control registers are “0” unless otherwise specified. 510Ω, 0.1%, resistor connected between R1
and Vss, and another between R2 and Vss unless otherwise specified. 400kHz TTL input at SCL unless otherwise
specified. SDA pulled to Vcc through an external 2kΩ resistor unless otherwise specified. 2-wire interface in “standby”
(see notes 1 and 2 on page 22), unless otherwise specified. WP, A0, A1, and A2 floating unless otherwise specified.
VRef pin unloaded, unless otherwise specified.
Temperature
Temperature while writing to memory
Voltage on Vcc Pin
Voltage on any other Pin
Iccstby
Iccfull
Iccwrite
I
V
V
I
V
I
V
PLDN
INTTL
OHSDA
VRef and VSense.................................... -0.50 to 1 mA
ILTTL
IHTTL
OLSDA
ILCMOS
Symbol
Standby current into Vcc
pin
Full operation current into
Vcc pin
Nonvolatile Write current
into Vcc pin
On-chip pull down
current at WP, A0, A1,and
A2
SCL and SDA, input Low
voltage
SCL and SDA, input High
voltage
SCL and SDA input
current
SDA output Low voltage
SDA output High current
WP, A0, A1, and A2 input
Low voltage
Parameter
22
...................... 0 to 5 mA
................ -1.0V to +7V
Parameter
Min
2.0
-1
0
0
0
0
X9530
Typ
4
1
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
0.2 x
Max
100
Vcc
0.8
0.4
20
10
2
9
Unit
mA
mA
mA
μA
μA
μA
V
V
V
V
R1 and R2 floating, VRef unloaded.
2-wire interface reading from
memory, I
Vss, DAC input bytes: FFh, VRef
unloaded.
Average from START condition until
t
WP: Vcc, R1 and R2 floating,
VRef unloaded.
V(WP), V(A0), V(A1), and V(A2) from
0V to Vcc
Pin voltage between 0 and Vcc, and
SDA as an input.
I(SDA) = 2 mA
V(SDA) = Vcc
WP
after the STOP condition
Test Conditions / Notes
Min.
-0.3
-40
3
0
1
and I
2
Vcc + 0.3
both connected to
Max.
+100
+70
5.5
November 11, 2005
Units
°C
°C
V
V
FN8211.1