CAT3647HV3-GT2 ON Semiconductor, CAT3647HV3-GT2 Datasheet - Page 9

• Manufacturer Part Number: CAT3647HV3-GT2
• Description: IC LED DRVR WHITE BCKLGT 16-TQFN
• Manufacturer: ON Semiconductor
• Series: QUAD-Mode®r
• Type: Backlight, White LEDr

Specifications of CAT3647HV3-GT2

• Topology: Switched Capacitor (Charge Pump)
• Number Of Outputs: 3
• Internal Driver: Yes
• Type - Primary: Backlight
• Type - Secondary: White LED
• Frequency: 800kHz ~ 1.6MHz
• Voltage - Supply: 2.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 16-TFQFN Exposed Pad
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 30mA
• Internal Switch(s): Yes
• Efficiency: 92%
• Number Of Segments: 3
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Details
• Other names: CAT3647HV3-GT2TR

Pin Function
VIN is the supply pin for the charge pump. A small 1 mF
ceramic bypass capacitor is required between the VIN pin
and ground near the device. The operating input voltage
range is from 2.5 V to 5.5 V. Whenever the input supply falls
below the under-voltage threshold (1.8 V), all the LED
channels are disabled and the device enters shutdown mode.
EN/DIM is the enable and one wire dimming input for all
LED channels. Levels of logic high and logic low are set at
1.3 V and 0.4 V respectively. When EN/DIM is initially
taken high, the device becomes enabled and all LED
currents are set to the full scale according to the resistor
R
mode, the EN/DIM pin must be held low for at least 1.5 ms.
VOUT is the charge pump output that is connected to the
LED anodes. A small 1 mF ceramic bypass capacitor is
required between the VOUT pin and ground near the device.
GND is the ground reference for the charge pump. The pin
must be connected to the ground plane on the PCB.
Table 6. PIN DESCRIPTION
SET
. To place the device into “zero current” shutdown
EN/DIM
Name
RSET
VOUT
LED1
LED2
LED3
GND
GND
C1+
C2+
VIN
C1-
C2-
NC
LED1 cathode terminal.
LED2 cathode terminal.
LED3 cathode terminal.
Connect resistor RSET to set the LED current.
Device enable (active high) and Dimming Control.
Charge pump output connected to the LED anodes.
Charge pump input, connect to battery or supply.
Bucket capacitor 1 Positive terminal
Bucket capacitor 1 Negative terminal
Bucket capacitor 2 Positive terminal
Bucket capacitor 2 Negative terminal
Ground Reference
Not connected inside package.
Connect to GND on the PCB.
http://onsemi.com
9
C1+, C1- are connected to each side of the ceramic bucket
capacitor C
C2+, C2- are connected to each side of the ceramic bucket
capacitor C
LED1, LED2, LED3 provide the internal regulated current
sources for each of the LED cathodes. These pins enter
high-impedance zero current state whenever the device is
placed in shutdown mode.
TAB is the exposed pad underneath the package. For best
thermal performance, the tab should be soldered to the PCB
and connected to the ground plane.
RSET is connected to the resistor (R
current for the LEDs. The voltage at this pin regulated to
0.6 V. The ground side of the external resistor should be star
connected back to the GND of the PCB. In shutdown mode,
RSET becomes high impedance.
Function
1
2
.
.
SET
) to set the full scale