LDP10IG10-A Panduit Corp, LDP10IG10-A Datasheet - Page 136

• Manufacturer Part Number: LDP10IG10-A
• Description: RACEWAY 1CHAN LG AD LGY(10=10')
• Manufacturer: Panduit Corp
• Series: Pan-Way™r

Specifications of LDP10IG10-A

• Wire Duct Type: Solid (Raceway), Single Channel
• Height: 0.860" (21.80mm)
• Length: 10.00' (3.05m)
• Width: 1.51" (38.4mm)
• Mounting Type: Adhesive
• Features: Attached Latching Lid
• Color: Gray, Light

Faceplates,
Furniture
LD Profile
Overview
Selection
Technical
Ultimate
Labeling
Twin-70
Glossary
Boxes &
System
System
Office
Outlet
Quick
Guide
TG-70
Index
Cove
T130
T-70
T-45
Pole
Info
ID
&
&
N8
P
LD non-metallic single channel, one-piece design, adhesive backed, hinged cover surface raceway, shall be used to route,
protect, and conceal low voltage data, voice, and video cabling. The raceway will include a full complement of bend radius
control (BRC) and standard fittings consisting of, but not limited to: elbows (internal and external), couplings for joining
raceway sections, blank end fittings for closing open ends of the raceway, entrance end fittings, reducer fittings, and tee
fittings. The BRC fittings shall incorporate a minimum 1" bend radius as recommended for Category 5e & 6 UTP and fiber
optic cables, in TIA/EIA-568-B. LD raceway will be manufactured in 2 different lengths from impact resistant material with
flammability rating of V-0. LD raceway finish shall be pure color and will resist scratches and dents and will not peel or
corrode. LD raceway shall be available in three sizes and four standard colors and shall be optimized for use with the
PANDUIT
P
LDS non-metallic surface raceway will be a one piece, solid raceway used to route, protect, and conceal data network, voice
or power cabling. The raceway shall be listed as suitable for use in applications having up to 600 volts between conductors by
Underwriters Laboratories, Inc. per standard 5A when screw secured with mounting straps and per installation instructions.
The raceway shall be manufactured from impact resistant material with flammability rating of UL94V-0. A full complement of
power, 1" bend radius control (BRC), and standard snap-on fittings must be available. All fittings and boxes shall be tamper
resistant to prevent unauthorized access to cables. LDS raceway finish shall be pure color and will resist scratches and dents
and will not peel or corrode. It shall be optimized for use with the PANDUIT
P
T130 non-metallic multi-channel surface raceway shall be used to route, protect, and conceal power and/or communications
cabling. The raceway shall be listed as suitable for use in applications up to 600 volts between conductors by Underwriters
Laboratories, Inc. per standard 5A, and by Canadian Standards Association, Inc. per 22.2 no. 62.01-03, when screw
secured and installed per instructions. A full complement of power rated fittings must be available as well as device brackets
to install a variety of communication and electrical devices. Divider wall must be available to form separate channels in the
multi-channel raceway. T130 raceway must be tamper resistant yet also allow access for moves, adds, and changes and must
be manufactured from impact resistant material with a flammability rating of V-0. T130 raceway finish shall be pure color and
will resist scratches and dents and will not peel or corrode. T130 raceway mounting brackets shall be available to mount to
irregular mounting surfaces. T130 raceway shall be available in three standard colors and shall be optimized for use with the
PANDUIT
P
The Aluminum Outlet Poles shall be an aluminum channel with a cross sectional area of 2.90" x 1.77", available in 11 or
13 foot lengths in two standard colors. The Power and Communication Pole shall consist of two compartments and be UL-5
listed and CSA certified to 600V. The pole shall be supplied with a power entry box with ½ conduit breakouts and 8"
removable plate. One compartment shall be factory wired with two duplex style 20A, 125V NEMA 5-2OR grounding-type
specification grade receptacles and the second compartment left blank for field installation of telephone, data network or
other low voltage cabling. The Communications Only Pole shall consist of one compartment for field installation of telephone,
data network or other low voltage cabling. Both pole versions shall be capable of accepting 70mm snap-on faceplates as well
as NEMA standard screw mount faceplates and be provided with a non-metallic 70mm (2.75") cover, 1" bend radius entry
fitting and t-bar mounting bracket, ceiling trim plates and floor end cap with grip pad.
AN
AN
AN
AN
Order number of pieces required, in multiples of Standard Package Quantity.
-W
-W
-W
-W
AY
AY
AY
AY
®
®
®
®
®
®
P
P
LD Surface Raceway
LDS Surface Raceway
Type T130 Surface Raceway
P
AN
AN
AN
-N
-N
-P
ET
ET
OLE
®
®
Communication System.
Communication System.
™
Aluminum Outlet Poles for Power and Communication
®
P
AN
-N
ET
®
Communication System.
Prime items appear in BOLD.