LDP10WH10-A Panduit Corp, LDP10WH10-A Datasheet - Page 137

• Manufacturer Part Number: LDP10WH10-A
• Description: RACEWAY 1CHAN LG AD WH(10=10')
• Manufacturer: Panduit Corp
• Series: Pan-Way™r

Specifications of LDP10WH10-A

• Wire Duct Type: Solid (Raceway), Single Channel
• Height: 0.860" (21.80mm)
• Length: 10.00' (3.05m)
• Width: 1.51" (38.4mm)
• Mounting Type: Adhesive
• Features: Attached Latching Lid
• Color: White

The UL and CSA marks found on PANDUIT
components have been evaluated in accordance with the UL 5A/CSA 22.2 No. 62.1-03 standards. Our systems
meet or exceed the requirements of ALL (not just some) of the tests outlined. This assures the end user of a
quality product which will perform in a safe manner when installed as recommended.
A product bearing UL/CSA complies with the following:
• Utilizes a UL RECOGNIZED material, which meets specific product property requirements, such as volume
• FLAMMABILITY: The system materials have a flammability rating of V-0. The finished part complies with
• LOW TEMPERATURE HANDLING AT -34°C: This test assures that the raceway integrity will remain intact
• COLD TEMPERATURE IMPACT AT 0°C: A 1.18lb steel sphere is dropped from a height of 51 inches to
• CRUSH: Both raceway and fittings are subjected to a compressive load of 300 lbs., which is maintained for
• MOLD STRESS: During the cooling process, stresses may be frozen in the raceway or fitting. This test
• TEMPERATURE TEST: The raceway undergoes a several hour test to determine the maximum number of
• TRIAL INSTALLATION: This is conducted to verify that the recommended installation instructions and
• RECEPTACLE SECURENESS: Assures that a receptacle shall remain secure in the raceway when a power
• SECURITY OF KNOCKOUT AND BREAKAWAY TAB: A knockout or breakaway tab shall remain intact
• HINGE CYCLING: A section of hinged raceway is mounted per instruction sheet. The raceway is then opened
NOTE: The information provided above is intended for use only as a guideline. Please refer to the specified document for detailed test descriptions or
standards information.
resistivity, hot wire ignition, high current arc ignition, dielectric strength and heat deflection temperature.
flammability rating of 5VA. Both the raceway and associated fittings exhibit self-extinguishing characteristics.
under typical conditions encountered during shipment and handling in a hostile subzero temperature.
produce an impact of 5 ft.-lbs. This test simulates the impact resistance of the product when subjected to a
cold temperature extreme following installation, such as cold storage or an area without heat.
one minute. This load is twice the weight of an average person. Following the removal of the load, both the
raceway and fittings must remain intact and show an acceptable level of permanent deformation.
conditions the product in an air-circulating oven for seven (7) hours at the maximum intended useful
temperature of the system. After cooling to room temperature the raceway system with cover must remain
intact and secure.
electrical conductors to operate the system. This assures the end use that the power conductors and raceway
will not exceed their respective temperature rating during their intended operation.
mounting hardware are effective and that the system maintains a complete and safe enclosure of conductors.
cord attachment plug is inserted and a 25 lb. weight is applied for 60 seconds. This test is conducted with the
receptacle positioned horizontally to the ground and then repeated with receptacle face at a 30° angle to the
power cord.
following a force application of 10 lbs. for 60 seconds. Following the removal of a tab, no sharp edges shall be
left which could cause abrasion of the conductor insulation. This test assures that the tab can resist an applied
force but can be removed easily per recommended instructions.
90 degrees from its initial position and closed, without latching for 100 cycles. The hinge shall have no
functional damage. This assures a safe lifetime of intended use.
(Standard for Safety of Non-Metallic Surface Raceways and Fittings)
UL-CSA Performance Requirements
For service and technical support, call 800-777-3300 (outside the U.S. and Canada, see back cover).
®
non-metallic surface raceway systems assures that the raceway
N9
Faceplates,
Furniture
LD Profile
Overview
Selection
Technical
Ultimate
Labeling
Twin-70
Boxes &
Glossary
System
System
Office
Outlet
Quick
Guide
TG-70
Index
Cove
T130
T-70
T-45
Pole
Info
ID
&
&