MCZ33937EK Freescale Semiconductor, MCZ33937EK Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/2/262/freescale_semiconductor_sml.jpg)
MCZ33937EK
Manufacturer Part Number
MCZ33937EK
Description
IC PRE-DRIVER 3PHASE 54-SOIC
Manufacturer
Freescale Semiconductor
Series
SMARTMOS™r
Datasheet
1.MCZ33937AEKR2.pdf
(48 pages)
Specifications of MCZ33937EK
Configuration
3 Phase Bridge
Input Type
Non-Inverting
Delay Time
265ns
Current - Peak
600mA
Number Of Configurations
1
Number Of Outputs
3
High Side Voltage - Max (bootstrap)
15V
Voltage - Supply
8 V ~ 40 V
Operating Temperature
-40°C ~ 135°C
Mounting Type
Surface Mount
Package / Case
54-SOIC (7.5mm Width) Exposed Pad, 54-eSOIC, 54-HSOIC
Product
H-Bridge Drivers
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
complementary output to immediately turn off and the
selected one to turn on after the deadtime delay as illustrated
in
corresponding FET was commanded off (see
Figure
BOOTSTRAP SUPPLY (VLS)
the bootstrap capacitors. It also supplies the peak currents
required for the Low Side gate drivers.
which is supplied from the VPWR pin. This pin can be
connected to system battery voltage and is capable of
withstanding up to the full load dump voltage of the system.
However, the IC only requires a low-voltage supply on this
pin, typically 13 to 16 V. Higher voltages on this pin will
increase the IC power dissipation.
This limits the gate voltage capable of being applied to the
FETs and reduces system performance due to the higher
FET on-resistance. To allow a higher gate voltage to be
supplied, the IC also incorporates a charge pump. The
switches and control circuitry are internal; the capacitors and
diodes are external (see
LOW SIDE DRIVERS
FETs. The circuits provide a low-impedance drive to the gate,
ensuring the FETs remain off in the presence of high dV/dt
transients on their drains. Additionally, these output drivers
isolate the other portions of the IC from currents capable of
being injected into the substrate due to rapid dV/dt transients
on the FET drains.
Low Side FETs. The Low Side drivers are capable of
providing a typical peak current of 2.0 A. This gate drive
current may be limited by external resistors in order to
achieve a good trade-off between the efficiency and EMC
(Electro-Magnetic Compatibility) compliance of the
application. the Low Side driver uses High Side PMOS for
turn on and Low Side isolated LDMOS for turn off. The circuit
ensures the impedance of the driver remains low, even
28
33937
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
Figure
This is the portion of the IC providing current to recharge
The power for the gate drive circuits is provided by VLS
In 12 V systems the supply voltage can fall as low as 6.0 V.
These three drivers turn on and off the external Low Side
Low Side drivers switch power from VLS to the gates of the
Figure 16. Edge Sensitive Logic Inputs (Phase A)
PA _HS
PA_LS
PA_HS_G
PA_LS_G
16).
16. The deadtime delay timer starts when the
Figure
De adt ime
De lay
22).
Figure 6
and
during periods of reduced current. Current limit is blanked
immediately after subsequent input state change in order to
ensure device stays off during dV/dt transients.
HIGH SIDE DRIVERS
bootstrap capacitor to the external High Side FETs. The
circuits provide a low-impedance drive to the gate, ensuring
the FETs remain off in the presence of high dV/dt transients
on their sources. Further, these output drivers isolate the
other portions of the IC from currents capable of being
injected into the substrate due to rapid dV/dt transients on the
FETs.
capacitor to the gate of the external High Side FET, thus
turning the High Side FET on. The High Side driver uses a
level shifter, which allows the gate of the external High Side
FET to be turned off by switching to the High Side FET
source.
obtained from the bootstrap supply, so, a short time is
required after the application of power to the IC to charge the
bootstrap capacitors. To ensure this occurrence, the internal
control logic will not allow a High Side switch to be turned on
after entering the ENABLE state until the corresponding Low
Side switch is enabled at least once. Caution must be
exercised after a long period of inactivity of the Low Side
switches to verify the bootstrap capacitor is not discharged. It
will be charged by activating the Low Side switches for a brief
period, or by attaching external bleed resistors from the
HS_S pins to GND.
CAUTION for 33937 only (Use the 33937A to avoid this
CAUTION)
bootstrap capacitors requires extra care to insure the
transient induced when charging fully depleted capacitors
does not cause an unintended power on reset. The 33937A
has been modified to eliminate the need for these special
considerations. Factors which affect the sensitivity to this
effect are, bootstrap capacitor size, VLS filter capacitor size,
VLS voltage and the junction temperature. The effect is more
pronounced for greater values of these parameters. It is also
more pronounced if all phases charge depleted capacitors
simultaneously. For balanced capacitance on VLS and
VLS_CAP of greater than 3.5 µF (total of 7.0 µF VLS
filtering), 1.2 µF bootstrap capacitance on each phase could
cause a POR at room temperature with VLS at 13 V. At the
worst case conditions of 15.4 V VLS voltage and 150°C
junction temperature, with the same total VLS capacitance of
7.0 µF, approximately 0.3 µF total (0.1µF each) on Px_BOOT
could cause the same effect. Since this characteristic is
intrinsic to the bootstrap diode integrated on the device, a
valid solution to prevent an undesired reset during
initialization would be to use external diodes between VLS
and the Px_BOOT pin.
These three drivers switch the voltage across the
The High Side drivers deliver power from their bootstrap
The gate supply voltage for the High Side drivers is
Using the 33937 in applications which use large value
Analog Integrated Circuit Device Data
Freescale Semiconductor