E-L9935013TR STMicroelectronics, E-L9935013TR Datasheet - Page 19
![IC STEPPER MOTOR DVR 2PH 20PWRSO](/photos/6/93/69347/497-20-powersoic_series_sml.jpg)
E-L9935013TR
Manufacturer Part Number
E-L9935013TR
Description
IC STEPPER MOTOR DVR 2PH 20PWRSO
Manufacturer
STMicroelectronics
Type
2 Phase Stepper Motor Driverr
Datasheet
1.L9935.pdf
(29 pages)
Specifications of E-L9935013TR
Applications
Stepper Motor Driver, 2 Phase
Number Of Outputs
1
Current - Output
±1.2A
Voltage - Supply
8 V ~ 24 V
Operating Temperature
-40°C ~ 150°C
Mounting Type
Surface Mount
Package / Case
PowerSO-20 Exposed Bottom Pad
Product
Stepper Motor Controllers / Drivers
Operating Supply Voltage
14.4 V
Supply Current
4.5 mA
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Load
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
497-10346-2
E-L9935013TR
E-L9935013TR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
L9935
5.12
5.13
Limitation of the diagnosis
The diagnosis depends on either detecting an overcurrent of more than typically 1.8 A
through the source transistor or on not detecting a flyback pulse, or on detecting severe
overcurrents of the sink transistor immediately after turn on.
●
●
●
●
●
Partial shorts of windings or shorts of stepper motors with coils in series may still yield a
flyback pulses that are accepted by the diagnosis as a proper signal.
Table 8.
At stepping rates faster than 1ms/data transfer error flags indicating a short should be used
to initiate a pause of at least 1ms to allow the power bridges to cool down again.
Serial data interface (SPI)
The serial data interface itself consists of the pins SCL (serial clock), SDI (serial data input)
and SDO (serial data output).
To especially support bus controlled applications the additional signals
and CSN (chip select not) are available.
Error 1 bit7 Error 2 bit6
Small currents bypassing the load will not be detected.
In the low current range (hold current) the flyback pulse (especially commutating
against the supply voltage after changing phase) may (depending on the inductivity of
the stepper motor windings) be too short to be detected correctly. For this reason
diagnosis using the flyback pulse is blanked at phase reversal at hold current.
In the low current range (hold current) the current capability of the bridge is reduced on
purpose. Short to V
normal operation.
Flyback pulse detection is not blanked during PWM regulation at hold current (here
commutation voltage is less than 1V thus providing a longer pulse duration.) This
however should be taken in account using stepper motors with low inductivity (less than
0.5mH). Using motors with such a low inductivity the flyback voltage in hold mode may
decay too fast.
Motors with extremely low ohmic resistance tend to pump up the current because
current decay during flyback approaches zero while at bridge turn on the current will
increase. This may lead to overcurrent detection. We suggest to use stepper motors
with an ohmic resistance of approximately 3 Ω or more.
H
H
L
L
Diagnosis description - bit7 and bit6
H
H
L
L
S
Normal operation
Short to VS (sink overload immediately after turn on) shorted load (no
flyback) open load (no flyback)
short to gnd (source overload, missing flyback is masked)
over temperature pre alarm
may not be detected. In stead the bridge may just chop like
Doc ID 5198 Rev 9
Description
Functional description
EN
(chip enable not)
19/29