TPD4123K(Q) Toshiba, TPD4123K(Q) Datasheet
TPD4123K(Q)
Specifications of TPD4123K(Q)
Related parts for TPD4123K(Q)
TPD4123K(Q) Summary of contents
Page 1
... The regulator of 7V (typ.) is built in. • Package: 26-pin DIP. This product has a MOS structure and is sensitive to electrostatic discharge. When handling this product, ensure that the environment is protected against electrostatic discharge. TOSHIBA Intelligent Power Device High Voltage Monolithic Silicon Power IC TPD4123K 1 TPD4123K HDIP26-P-1332-2 ...
Page 2
Pin Assignment Marking Part No. (or abbreviation code) TPD4123K TPD4123K 2 TPD4123K Lot Code. (Weekly code) 2008-05-14 ...
Page 3
Block Diagram REG Regulator Under- voltage Protection Input Control DIAG Under- Under- Under- voltage voltage voltage Protection Protection Protection High-side ...
Page 4
Pin Description Pin No. Symbol 1 GND Ground pin Unused pin, which is not connected to the chip internally Unused pin, which is not connected to the chip internally. The control terminal of IGBT by the ...
Page 5
Equivalent Circuit of Input Pins Internal circuit diagram of HU, HV, HW, LU, LV, LW input pins 2 kΩ 2 kΩ HU/HV/HW LU/LV/LW 6.5 V 6.5 V Internal circuit diagram of RS pin kΩ 442 kΩ RS ...
Page 6
Timing Chart Input Voltage Output voltage TPD4123K 2008-05-14 ...
Page 7
Truth Table Input Mode Normal Over-current ...
Page 8
... Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). (Ta = 25° ...
Page 9
Electrical Characteristics Characteristics Operating power supply voltage Current dissipation Input voltage Input current Output saturation voltage FRD forward voltage BSD forward voltage Regulator voltage Current limiting voltage Current limiting dead time Thermal shutdown temperature Thermal shutdown hysteresis V under voltage ...
Page 10
Application Circuit Example 15V Regulator V REG + Control Microcomputer DIAG R ...
Page 11
External Parts Typical external parts are shown in the following table. Part Typical 25 V/2.2 μ 0.62 Ω ± V/10 μ ...
Page 12
Description of Protection Function (1) Over-current protection This product incorporates a over-current protection circuit to protect itself against over-current at startup or when a motor is locked. This protection function detects voltage generated in the current detection resistor connected to ...
Page 13
V H – T CEsat j 3 700 mA 3 500 mA 2.6 2 300 mA 1.8 1.4 − 100 Junction temperature T (°C) ...
Page 14
3 280 0.5 A High-side Low-side 2.0 1.0 0 − 100 Junction temperature T (° – ...
Page 15
I – (ON) BS 500 T =−40° =25° =135°C j 400 300 200 100 Control power supply voltage – 250 200 150 ...
Page 16
Test Circuits IGBT Saturation Voltage (U-phase low side) FRD Forward Voltage (U-phase low side) 0. TPD4123K ...
Page 17
V Current Dissipation CC Regulator Voltage IM 30mA VM 17 TPD4123K V = 15V 15V CC 2008-05-14 ...
Page 18
Output ON/OFF Delay Time (U-phase low side 90% 10% 90 off 18 TPD4123K 280V 560Ω 2.2μ ...
Page 19
V Under-voltage Protection Operating/Recovery Voltage (U-phase low side) CC *Note: Sweeps the V pin voltage from 15 V and monitors the U pin voltage. The V CC output is off defines the under-voltage protection operating voltage. Also sweeps from 6 ...
Page 20
Current Control Operating Voltage (U-phase high side) *Note: Sweeps the IS/RS pin voltage and monitors the U pin voltage. The IS/RS pin voltage when output is off defines the current control operating voltage. V Current Dissipation (U-phase high side) BS ...
Page 21
Turn-On/Off Loss (low side IGBT + high side FRD) Input (LU = PG) IGBT (C-E Voltage) (U-GND) Power Supply Current 5mH 2.2μ toff ton 21 TPD4123K 280V ...
Page 22
Package Dimensions HDIP26-P-1332-2.00 Weight: 3.8 g (typ.) Unit : mm 22 TPD4123K 2008-05-14 ...
Page 23
... Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ...