AMIS30621C6217G ON Semiconductor, AMIS30621C6217G Datasheet - Page 54

• Manufacturer Part Number: AMIS30621C6217G
• Description: IC MOTOR STEPPER DVR/CTLR 20SOIC
• Manufacturer: ON Semiconductor
• Type: Micro Stepping Motor Driverr

Specifications of AMIS30621C6217G

• Number Of Outputs: 4
• Voltage - Supply: 6.5 V ~ 29 V
• Operating Temperature: -40°C ~ 165°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (7.5mm Width)
• Product: Stepper Motor Controllers / Drivers
• Operating Supply Voltage: 6.5 V to 29 V
• Supply Current: 800 mA
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Applications: -
• Voltage - Load: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Where:
SetPositionShort
LIN Master to drive one, two or four motors to a given
absolute position. It applies only for half stepping mode
(StepMode[1:0] = “00”) and is ignored when in other
stepping modes. See Positioning for more details.
SetPositionShort can only be used with a network
Two different cases must be considered, depending on the programmed value of the ADMbit in the OTP memory.
The priority encoder table (See Priority Encoder) describes the cases where a SetPositionShort command will be
ignored.
SetPositionShort corresponds to the following LIN writing frames:
Where:
Table 55. SetPosition WRITING FRAME TYPE #4
Table 56. SetPositionShort WRITING FRAME TYPE #2
Adn[6:0]: Motor #n physical address (n ∈ [1,2]). Posn[15:0]: Signed 16−bit position set−point for motor #n.
This command is provided to the circuit by the
The physical address is coded on 4 bits, hence
(*) According to parity computation
Broad: If broad = ‘0’ all the stepper motors connected to the LIN bus will go to Pos[10:0].
ID[5:0]: Dynamically allocated identifier to two data bytes SetPositionShort command.
1. Two (2) data bytes frame for one (1) motor, with specific identifier (type #2)
Byte
Byte
0
1
2
3
4
5
6
7
8
9
0
1
2
3
ADM
0
1
1
Checksum
Checksum
Identifier
Identifier
Content
Content
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Data 8
Data 1
Data 2
AD[3]
X
0
1
Bit 7
Bit 7
0
1
1
1
*
Pos[10:8]
Bit 6
Bit 6
0
*
Pin HW0
http://onsemi.com
Bit 5
Bit 5
Tied to V
1
0
54
DD
implementing a maximum of 16 slave nodes. These 4 bits
are corresponding to the bits PA[3:0] in OTP memory. For
SetPositionShort operation: It is recommended to set
HW0 and HW1 to ’1’. If the ADM bit is set to ’1’ the PA0
bit in OTP has to programmed to ’1’. If the ADM bit is set
to ’0’, HW2 has to be set to ’1’.
Checksum over data
Checksum over data
Broad
Pin HW1
Bit 4
Bit 4
ID4
AppCMD = 0x80
1
Pos1[15:8]
Pos2[15:8]
Structure
Structure
Pos1[7:0]
Pos2[7:0]
Pos [7:0]
CMD[6:0] = 0x0B
AD1[6:0]
AD2[6:0]
Bit 3
Bit 3
ID3
1
Tied to GND
Tied to V
Tied to V
Pin HW2
Bit 2
Bit 2
ID2
1
BB
BB
AD [3:0]
Bit 1
Bit 1
ID1
0
Bit PA0 in OTP
memory
AD[0]
1
1
Bit 0
Bit 0
ID0
0