LTC3108EGN-1#PBF Linear Technology, LTC3108EGN-1#PBF Datasheet - Page 9

• Manufacturer Part Number: LTC3108EGN-1#PBF
• Description: IC VOLTAGE CONVERTER 16-SSOP
• Manufacturer: Linear Technology

Specifications of LTC3108EGN-1#PBF

• Applications: Energy Harvesting
• Current - Supply: 3mA
• Voltage - Supply: 20mV ~ 500mV
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 16-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

operaTion
Oscillator
The LTC3108-1 utilizes a MOSFET switch to form a resonant
step-up oscillator using an external step-up transformer
and a small coupling capacitor. This allows it to boost input
voltages as low as 20mV high enough to provide multiple
regulated output voltages for powering other circuits. The
frequency of oscillation is determined by the inductance of
the transformer secondary winding and is typically in the
range of 10kHz to 100kHz. For input voltages as low as
20mV, a primary-secondary turns ratio of about 1:100 is
recommended. For higher input voltages, this ratio can be
lower. See the Applications Information section for more
information on selecting the transformer.
Charge Pump and Rectifier
The AC voltage produced on the secondary winding of
the transformer is boosted and rectified using an external
charge pump capacitor (from the secondary winding to
pin C1) and the rectifiers internal to the LTC3108-1. The
rectifier circuit feeds current into the VAUX pin, provid-
ing charge to the external VAUX capacitor and the other
outputs.
VAUX
The active circuits within the LTC3108-1 are powered from
VAUX, which should be bypassed with a 1µF capacitor.
Larger capacitor values are recommended when using
turns ratios of 1:50 or 1:20 (refer to the Typical Applica-
tion examples). Once VAUX exceeds 2.5V, the main V
is allowed to start charging.
An internal shunt regulator limits the maximum voltage
on VAUX to 5.25V typical. It shunts to GND any excess
current into VAUX when there is no load on the converter
or the input source is generating more power than is
required by the load.
Voltage Reference
The LTC3108-1 includes a precision, micropower refer-
ence, for accurate regulated output voltages. This reference
becomes active as soon as VAUX exceeds 2V.
OUT
Synchronous Rectifiers
Once VAUX exceeds 2V, synchronous rectifiers in parallel
with each of the internal diodes take over the job of rectify-
ing the input voltage, improving efficiency.
Low Dropout Linear Regulator (LDO)
The LTC3108-1 includes a low current LDO to provide a
regulated 2.2V output for powering low power processors
or other low power ICs. The LDO is powered by the higher
of VAUX or V
as VAUX has charged to 2.3V, while the V
capacitor is still charging. In the event of a step load on
the LDO output, current can come from the main V
capacitor if VAUX drops below V
a 2.2µF ceramic capacitor for stability. Larger capacitor
values can be used without limitation, but will increase
the time it takes for all the outputs to charge up. The LDO
output is current limited to 4mA minimum.
V
The main output voltage on V
supply, and is user programmed to one of four regulated
voltages using the voltage select pins VS1 and VS2, ac-
cording to Table 2. Although the logic threshold voltage
for VS1 and VS2 is 0.85V typical, it is recommended that
they be tied to ground or VAUX.
Table 2. Regulated Voltage Using Pins VS1 and VS2
When the output voltage drops slightly below the regulated
value, the charging current will be enabled as long as VAUX
is greater than 2.5V. Once V
value, the charging current is turned off.
The internal programmable resistor divider sets V
eliminating the need for very high value external resistors
that are susceptible to board leakage.
OUT
VAUX
VAUX
GND
GND
VS2
OUT
. This enables it to become active as soon
VAUX
VAUX
GND
GND
VS1
OUT
OUT
is charged from the VAUX
has reached the proper
OUT
LTC3108-1
. The LDO requires
OUT
V
2.5V
3.7V
4.5V
3V
OUT
storage
OUT
31081f

OUT
,