HCPL-800J-500E Avago Technologies US Inc., HCPL-800J-500E Datasheet - Page 17

• Manufacturer Part Number: HCPL-800J-500E
• Description: OPTOCOUPLER DAA PLC ISO 16SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-800J-500E

• Applications: Powerline Data Access
• Current - Supply: 28mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SO-16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Receiver
The received signal from the powerline is often heavily
attenuated and also includes high level out of band
noise. Receiver performance can be improved by posi-
tioning a suitable filter prior to the Rx-in input (pin 10).
To counter the inevitable attenuation on the powerline,
the HCPL-800J receiver circuit includes a fixed 20 dB
front-end gain stage. If desired, this fixed gain can be
reduced to unity gain by inserting an impedance of 33
kΩ
ed to maintain the fixed gain of 20 dB at this position and
reduce the overall signal gain elsewhere if required. This
configuration will result in the best SNR and IMRR.
The optical isolated Rx signal appears at Rx-PD-out (pin
3). This signal is subsequently AC coupled to the final
gain stage via a capacitor.
The final gain stage consists of an op-amp configured in
an inverting configuration and DC biased at 2.27 V. The
actual gain of this gain stage is user programmable with
external resistors R1 and R2 as shown in Figure 25. The
signal output at Rx-out (pin 6) is buffered and may be
directly connected to the demodulator or ADC, using AC
coupling if required.
Internal Protection and Sensing
The HCPL-800J includes several sensing and protec-
tion functions to ensure robust operation under wide
ranging environmental conditions.
The first feature is the V
(UVD). In the event of V
than 4 V, the output status pin is switched to a logic low
state.
The next feature is the over-temperature shutdown. This
particular feature protects the line driver stage from
over-temperature stress. Should the IC junction temper-
ature reach a level above 130°C, the line driver circuit is
shut down, simultaneously the output of Status (pin 5) is
pulled to the logic low state.
The final feature is load detection function. The powerline
impedance is quite unpredictable and varies not just at
17
Receiver Mode
Transmitter Mode
in the receiver signal path. It is however recommend-
Normal
High
High
CC2
CC2
dropping to a voltage less
Under Voltage Detection
V
Low
Low
CC2
< 4 V
different connection points but is also time variant. The
HCPL-800J includes a current sense feature, which may
be utilized to feedback information on the instantaneous
powerline load condition. Should the peak current reach
a level greater than 0.6 A
pulled to a logic low state for the entire period the peak
current exceeds -0.3 A, as shown in Figure 29. Using the
period of the pulse together with the known coupling
impedance, the actual powerline load can be calculated.
Table 2 shows the logic output of the Status pin.
External Transient Voltage Protection
To protect the HCPL-800J from high voltage transients
caused by power surges and disconnecting/connecting
the modem, it is necessary to add an external 6.8 V bi-
directional transient voltage protector (as component
D1 shown in Figure 25).
Additional protection from powerline voltage surges
can be achieved by adding an appropriate Metal Oxide
Varistor (MOV) across the powerline terminals after the
fuse.
Figure 29. Transmit output load detection
Tx-out (pin 15)
0.5 A/Div
Status (pin 5)
2 V/Div
I
th
Over-Temperature
-
Low
PP
, the output of Status pin is
t
I
-
Low (pulsed)
th
Tx-out
t
th
< -0.3 A
2 µs/Div