SA56004EDP,118 NXP Semiconductors, SA56004EDP,118 Datasheet - Page 11

• Manufacturer Part Number: SA56004EDP,118
• Description: IC TEMP SENSOR 8-TSSOP
• Manufacturer: NXP Semiconductors

Specifications of SA56004EDP,118

• Package / Case: 8-TSSOP
• Output Type: I²C™/SMBus™
• Function: Temp Monitoring System (Sensor)
• Topology: ADC (Sigma Delta), Multiplexer, Register Bank
• Sensor Type: External & Internal
• Sensing Temperature: -40°C ~ 125°C, External Sensor
• Output Alarm: Yes
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 3 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Current: 1 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-3615 - DEMO BOARD I2C
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-3338-2; 935274567118; SA56004EDP-T

NXP Semiconductors
Table 14.
[1]
[2]
SA56004X_5
Product data sheet
Byte
Bit
Value
POR default RTOHB = RTOLB = 00h.
POR default RTOLB = 00h.
High byte (read/write address 11h)
sign
D7
RTOHB, RTOLB - Remote temperature offset registers
7.8.10 One-shot register
7.8.7 Programmable offset register (remote only)
7.8.8 ALERT mode register (AM)
7.8.9 Other registers
D6
64
Table 13.
[1]
Table 15.
Read and write address BFh.
D[7:1] is not defined and defaults to logic 0.
D0: The ALERT output is in interrupt mode when this bit is LOW. The ALERT output is in
comparator mode when this bit is HIGH.
The Manufacturers ID register has a default value A1h (1010 0001) and a read address
FEh.
The Die Revision Code register has a default value 00h (0000 0000) and read address
FFh. This register will increment by 1 every time there is a revision to the die.
The one-shot register is used to initiate a single conversion and comparison cycle when
the device is in the standby mode; upon completion of the single conversion cycle, the
device returns to the standby mode. It is not a data register; it is the write operation that
causes the one-shot conversion. The data written to this register is not stored; an FFh
value will always be read from this register. To initiate a one-shot operation, send a
standard write command with the command byte of 0Fh (One-Shot Write Address).
Byte
Bit
Value
Bit
Value
D5
32
POR default TH = 0Ah (10 C).
D4
16
TH - T_CRIT hysteresis register
AM - ALERT mode register
D7
D3
Single high byte (read/write address 21h)
0
8
D7
-
D2
[1]
4
D6
0
Rev. 05 — 22 May 2008
D6
D1
2
-
Digital temperature sensor with overtemperature alarms
D5
0
D0
1
D5
-
Low byte (read/write address 12h)
0.5
D7
D4
0
0.25
D4
16
D6
D3
0
0.125
D5
[1]
D3
8
D4
D2
0
0
D2
4
D3
0
SA56004X
D1
0
[2]
© NXP B.V. 2008. All rights reserved.
D2
0
D1
2
ALERT mode
D1
0
D0
11 of 36
D0
1
D0
0