L6910G STMicroelectronics, L6910G Datasheet - Page 11

• Manufacturer Part Number: L6910G
• Description: IC PWM BUCK BST VM 16SOICN
• Manufacturer: STMicroelectronics

Specifications of L6910G

• Pwm Type: Voltage Mode
• Number Of Outputs: 1
• Frequency - Max: 230kHz
• Duty Cycle: 100%
• Voltage - Supply: 5 V ~ 12 V
• Buck: Yes
• Boost: Yes
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 16-SOIC (3.9mm Width)
• Frequency-max: 230kHz
• Topology: Step Down
• Output Voltage: 0.9 V to 12 V
• Output Current: 1300 mA
• Switching Frequency: 50 KHz to 1000 KHz
• Duty Cycle (max): 100 %
• Maximum Operating Temperature: + 150 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Synchronous Pin: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 11. Asymptotic Bode Plot of Converter's Gain
5
The demo board shows the operation of the device in a general purpose application. This evaluation board al-
lows voltage adjustability from 0.9V to 5V through the switches S2-S5 according to the reported table when the
internal 0.9V reference is used (G1 closed). Output current in excess of 20A can be reached dependently on
the kind of mosfet used: up to three SO8 mosfet may be used for both High side and Low side switches. External
reference may be used for the regulation simply leaving open G1 and the switches S2-S5. The device may also
be disabled with the switch S1. The V
the V
to be closed and a 5V to 12V input can be directly connected to the V
copper thickness is of 70µm in order to minimize conduction losses considering the high current that the circuit
is able to deliver.The PGOOD signal is used as a logic level and it's been pulled up to V
other appropriate voltage available on the demo board. In case of input voltage higher than 7V (PGOOD Pin
Maximum Absolute Rating) a 5V reference is required. Figure 12 shows the demo board's schematic circuit
Figure 12. 15A Demo Board Schematic
15A DEMO BOARD DESCRIPTION
IN
input rail. The device is also able to operate with a single supply voltage; in this case the jumper G2 has
GNDREFIN
GNDREF
GNDCC
GNDIN
+VREF
REFIN
VCC
VIN
S1
S2
S3
S4
S5
F1
C17
G2
C16
C12
R6
SR12
SR13
C21
R10
R11
G1
R1
EAREF
VREF
GND
OSC
V
C15
SS
CC
D1
dB
COMP
CC
15
7
8
1
4
2
Modulator Gain
Compensation Network Gain
Error Amplifier
BOOT
R5/R3
L1
input rail supplies the device while the power conversion starts from
5
C19
12
D03IN1513
Error Amplifier
OCSET
R5
C18
R7
VFB
3
ω
6
Ζ1
ω
11
10
14
13
9
LC
ω
C14
C13
Ζ2
UGATE
PHASE
LGATE
PGND
PGOOD
R4
Closed Loop Gain
R3
ω
ESR
C20
ω
Q1-3
Q4-6
ω
P1
P2
IN
D2
R8
V
0.9
1.2
1.5
1.8
2.5
3.3
5.0
OUT
ω
input. The four layers demo board's
C1-C3
Open Open Open Open
Open
Open Open ON Open
Open Open Open ON
Open Open ON
C22
ON Open Open Open
ON
L2
R9
S2
ON
ON Open Open
S3
C4-
11
Open Open
S4
ON
S5
IN
R2
because there's no
V
GNDOUT
PWRGD
OUT
L6910G
11/26