HIP6311ACB-T Intersil, HIP6311ACB-T Datasheet
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
HIP6311ACB-T
Specifications of HIP6311ACB-T
Available stocks
Related parts for HIP6311ACB-T
HIP6311ACB-T Summary of contents
Page 1
... HIP6311ACB SOIC HIP6311ACBZ SOIC (See Note) (Pb-free) HIP6311ACBZA SOIC (See Note) (Pb-free) *Add “-T” suffix to part number for tape and reel packaging. NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations ...
Page 2
Block Diagram VSEN X 0.9 X1.15 AND FAULT COMP VID0 VID1 VID2 D/A VID3 VID4 FB 2 HIP6311A HIP6311A V PGOOD CC POWER-ON RESET (POR LATCH CLOCK AND S SAWTOOTH GENERATOR + ∑ + OVP - ...
Page 3
Simplified Power System Diagram VSEN PWM 1 PWM 2 HIP6311A PWM 3 PWM 4 VID Functional Pin Description 1 20 VID4 2 19 VID3 3 18 VID2 4 17 VID1 5 16 VID0 6 15 COMP ...
Page 4
Typical Application - 2 Phase Converter Using HIP6601 Gate Drivers +5V COMP VSEN PWM4 PWM3 PGOOD PWM2 VID4 VID3 PWM1 VID2 MAIN CONTROL VID1 HIP6311A VID0 ISEN4 ISEN3 FS/DIS ISEN2 ISEN1 GND 4 HIP6311A HIP6311A +12V BOOT ...
Page 5
Typical Application - 4 Phase Converter Using HIP6602 Gate Drivers FB COMP V VSEN CC ISEN1 PGOOD PWM1 VID4 PWM2 ISEN2 VID3 VID2 MAIN CONTROL VID1 HIP6311A VID0 ISEN3 FS/DIS PWM3 PWM4 GND ISEN4 5 HIP6311A HIP6311A +12V BOOT1 UGATE1 ...
Page 6
Absolute Maximum Ratings Supply Voltage .+7V ...
Page 7
ERROR AMPLIFIER CORRECTION - ∑ PROGRAMMABLE REFERENCE + ∑ DAC - I AVERAGE - + ∑ ∑ CORRECTION FIGURE 1. SIMPLIFIED BLOCK DIAGRAM OF THE HIP6311A VOLTAGE AND CURRENT CONTROL LOOPS FOR ...
Page 8
Correction circuit to the Comparator, reduces the output pulse width of the Comparator to compensate for the detected “above average” current in that channel. Droop Compensation In addition to control of each power ...
Page 9
Figure 3 shows the start-up sequence as initiated by a fast rising 5V supply, V applied to the HIP6311A. Note the CC, short rise to the three state level in PWM 1 output during first 32 PWM cycles. DELAY TIME ...
Page 10
MOSFETs, avoiding a possibly destructive ringing of the capacitors and output inductors. If the conditions that caused the over-voltage still persist, the PWM outputs will be cycled between three state and V clamped to ground, as ...
Page 11
COMP FB SAWTOOTH ERROR GENERATOR AMPLIFIER CORRECTION - + + - DIFFERENCE REFERENCE DAC TO OTHER CHANNELS TO OVER + CURRENT - TRIP COMPARATOR FIGURE 7. SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM SHOWING CURRENT AND VOLTAGE ...
Page 12
In order to fully utilize the output-voltage tolerance range, the output voltage is positioned in the upper half of the range when the output is unloaded and in the ...
Page 13
... Careful component selection, tight layout of the critical components, and short, wide circuit traces minimize the magnitude of voltage spikes. Contact Intersil for evaluation board drawings of the component placement and printed circuit board. There are two sets of critical components in a DC-DC converter using a HIP6311A controller and a HIP6601 gate driver ...
Page 14
IN LOCATE NEXT TO IC PIN( COMP C T HIP6311A R FB LOCATE NEXT PIN R IN VSEN FIGURE 11. PRINTED CIRCUIT BOARD POWER PLANES AND ISLANDS Component Selection Guidelines Output Capacitor ...
Page 15
Considerations section. With all else fixed, decreasing the inductance could increase the power dissipated in the MOSFETs by 30%. 1.0 SINGLE 0.8 CHANNEL 0.6 2 CHANNEL 0.4 3 CHANNEL 0.2 4 CHANNEL 0 0.1 0.2 0 DUTY CYCLE (V FIGURE ...
Page 16
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...