ISL6236IRZA-TKR5281 Intersil, ISL6236IRZA-TKR5281 Datasheet - Page 19

• Manufacturer Part Number: ISL6236IRZA-TKR5281
• Description: IC QUAD OUT POWER CONTROL 32-QFN
• Manufacturer: Intersil

Specifications of ISL6236IRZA-TKR5281

• Applications: Controller, Notebook Computers
• Voltage - Input: 5.5 ~ 25 V
• Number Of Outputs: 4
• Operating Temperature: -40°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Other names: ISL6236IRZA-TKR5281TR

Typical Performance Curves
Typical Application Circuits
The typical application circuits (Figures 66, 67 and 68)
generate the 5V/7A, 3.3V/11A, 1.25V/5A, dynamic voltage/10A,
1.5V/5A, 1.05V/5A and external 14V charge pump main
supplies in a notebook computer. The ISL6236 is also equipped
with a secondary feedback, SECFB, used to monitor the output
of the 14V charge pump. In an event when the 14V drops
below its threshold voltage, SECFB comparator will turn on
LGATE1 for 300ns. This will refresh an external 14V charge
pump without overcharging the output voltage. The input supply
range is 5.5V to 25V.
Detailed Description
The ISL6236 dual-buck, BiCMOS, switch-mode
power-supply controller generates logic supply voltages for
notebook computers. The ISL6236 is designed primarily for
battery-powered applications where high efficiency and
low-quiescent supply current are critical. The ISL6236
FIGURE 63. LOAD TRANSIENT V
V
OUT1
LGATE1 5V/DIV
RIPPLE 50mV/DIV
IL1 5A/DIV
19
V
OUT2
OUT1
FIGURE 65. LOAD TRANSIENT V
RIPPLE 20mV/DIV
= 1.5V (SKIP)
Circuit of Figures 66, 67 and 68, no load on LDO, OUT1, OUT2, V
EN2 = EN1 = VCC, V
otherwise noted. Typical values are at T
V
OUT2
V
OUT1
LGATE2 5V/DIV
RIPPLE 20mV/DIV
RIPPLE 20mV/DIV
ISL6236
BYP
= 5V, PVCC = 5V, V
provides a pin-selectable switching frequency, allowing
operation for 200kHz/300kHz, 400kHz/300kHz, or
400kHz/500kHz on the SMPSs.
Light-load efficiency is enhanced by automatic Idle-Mode
operation, a variable-frequency pulse-skipping mode that
reduces transition and gate-charge losses. Each step-down,
power-switching circuit consists of 2 N-channel MOSFETs, a
rectifier, and an LC output filter. The output voltage is the
average AC voltage at the switching node, which is
regulated by changing the duty cycle of the MOSFET
switches. The gate-drive signal to the N-channel high-side
MOSFET must exceed the battery voltage, and is provided
by a flying-capacitor boost circuit that uses a 100nF
capacitor connected to BOOT.
Both SMPS1 and SMPS2 PWM controllers consist of a
triple-mode feedback network and multiplexer, a multi-input
PWM comparator, high-side and low-side gate drivers and
OUT1
FIGURE 64. LOAD TRANSIENT V
= 1.05V (SKIP)
A
= +25°C. (Continued)
IL2 5A/DIV
EN LDO
V
OUT1
LGATE2 5V/DIV
IL1 5A/DIV
V
= 5V, T
OUT2
RIPPLE 20mV/DIV
RIPPLE 20mV/DIV
A
= -40°C to +100°C, unless
REF3
OUT1
, and REF, V
= 1.05V (PWM)
IN
April 29, 2010
= 12V,
FN6373.6