LM3481MM/NOPB National Semiconductor, LM3481MM/NOPB Datasheet
![IC CTLR LOW SIDE N-CH SW 10MSOP](/photos/6/60/66087/pkg_mub10a_sml.jpg)
LM3481MM/NOPB
Specifications of LM3481MM/NOPB
Available stocks
Related parts for LM3481MM/NOPB
LM3481MM/NOPB Summary of contents
Page 1
... Power saving shutdown mode reduces the total supply current to 5µA and allows power supply sequencing. Internal soft-start limits the inrush current at start-up. Typical Application Circuit © 2011 National Semiconductor Corporation LM3481/LM3481Q Key Specifications ■ Wide supply voltage range of 2.97V to 48V ■ ...
Page 2
Connection Diagram Package Marking and Ordering Information Order Number Package Type LM3481MM MSOP-10 LM3481MMX MSOP-10 LM3481QMM MSOP-10 LM3481QMMX MSOP-10 *Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is ...
Page 3
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. V pin Voltage IN FB Pin Voltage FA/SYNC/SD Pin Voltage COMP Pin Voltage UVLO Pin Voltage V Pin Voltage CC DR Pin Voltage I Pin Voltage ...
Page 4
Symbol Parameter Current Sense Threshold V SENSE Voltage Over Load Current Limit V SC Sense Voltage Internal Compensation V SL Ramp Voltage Output Over-voltage V Protection (with respect to OVP feedback voltage) (Note Output Over-Voltage V OVP(HYS) Protection Hysteresis Error ...
Page 5
Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings indicates conditions for which the device is intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and test ...
Page 6
Efficiency vs. Load Current (9V COMP Pin Source Current vs. Temperature I vs. Input Voltage (Switching) Supply www.national.com and 12V ) IN OUT 20136550 I Supply 20136552 Shutdown Threshold Hysteresis vs. Temperature 20136554 6 Frequency vs. Temperature 201365a7 vs. Input ...
Page 7
Drive Voltage vs. Input Voltage Current Sense Threshold vs. Input Voltage Minimum On-Time vs. Temperature Short Circuit Protection vs. V 20136557 Compensation Ramp Amplitude vs. Input Voltage 20136559 201365a8 7 IN 20136558 20136560 www.national.com ...
Page 8
Functional Block Diagram Functional Description The LM3481 uses a fixed frequency, Pulse Width Modulated (PWM), current mode control architecture typical appli- cation circuit, the peak current through the external MOSFET is sensed through an external sense resistor. The ...
Page 9
FIGURE 1. Basic Operation of the PWM comparator OVER VOLTAGE PROTECTION The LM3481 has over voltage protection (OVP) for the output voltage. OVP is sensed at the feedback pin (FB anytime the voltage at the feedback pin rises ...
Page 10
FIGURE 3. Compensation Ramp Avoids Sub-Harmonic Oscillation To prevent the sub-harmonic oscillations, a compensation ramp is added to the control signal, as shown in With the compensation ramp, ΔV samp1 criteria are expressed by, The compensation ramp has been added ...
Page 11
A more general equation for the slope compensation ramp shown below to include ΔV M caused by the resistor Δ good ...
Page 12
FIGURE 9. Shutdown Operation in Frequency Adjust Mode FIGURE 10. Shutdown Operation in Synchronization Mode www.national.com FIGURE 7. Frequency Adjust FIGURE 8. Frequency Synchronization 12 20136514 20136515 20136516 20136517 ...
Page 13
Under Voltage Lockout (UVLO) Pin The UVLO pin provides user programmable enable and shut- down thresholds. The UVLO pin is compared to an internal reference of 1.43V (typical), and a resistor divider programs . When the IC is enabled, a ...
Page 14
POWER INDUCTOR SELECTION The inductor is one of the two energy storage elements in a boost converter. Figure 13 shows how the inductor current varies during a switching cycle. The current through an in- ductor is quantified as: FIGURE 13. ...
Page 15
Combining the two equations yields an expression for R CURRENT LIMIT WITH ADDITIONAL SLOPE COMPENSATION If an external slope compensation resistor is used (see 5) the internal control signal will be modified and this will have an effect on the ...
Page 16
Reverse transfer capacitance Maximum drain to source voltage, V The off-state voltage of the MOSFET is approximately equal to the output voltage the MOSFET must be DS(MAX) greater than the output voltage. The power losses ...
Page 17
The bottom schematic shows the currents we refer currents. They are the most critical ones since current is changing in very short time periods. The dotted lined traces of the ...
Page 18
Designing SEPIC Using LM3481 Since the LM3481 controls a low-side N-Channel MOSFET, it can also be used in SEPIC (Single Ended Primary Induc- tance Converter) applications. An example of SEPIC using the LM3481 is shown in Figure 17. As shown ...
Page 19
SELECTION OF INDUCTORS L1 AND L2 Proper selection of the inductors L1 and L2 to maintain con- stant current mode requires calculations of the following pa- rameters. Average current in the inductors L2AVE OUT Peak to peak ...
Page 20
Input Capacitor Selection Similar to a boost converter, the SEPIC has an inductor at the input. Hence, the input current waveform is continuous and triangular. The inductor ensures that the input capacitor sees fairly low ripple currents. However, as the ...
Page 21
Physical Dimensions inches (millimeters) unless otherwise noted 10-Lead MSOP Package NS Package Number MUB10A 21 www.national.com ...
Page 22
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...