LM3481MM/NOPB National Semiconductor, LM3481MM/NOPB Datasheet - Page 13
![IC CTLR LOW SIDE N-CH SW 10MSOP](/photos/6/60/66087/pkg_mub10a_sml.jpg)
LM3481MM/NOPB
Manufacturer Part Number
LM3481MM/NOPB
Description
IC CTLR LOW SIDE N-CH SW 10MSOP
Manufacturer
National Semiconductor
Type
Step-Up (Boost), Flyback, Sepicr
Datasheet
1.LM3481MMNOPB.pdf
(22 pages)
Specifications of LM3481MM/NOPB
Internal Switch(s)
No
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
Adjustable
Current - Output
1A
Frequency - Switching
100kHz ~ 1MHz
Voltage - Input
2.97 ~ 48 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
For Use With
LM3481EVAL - BOARD EVAL FOR LM3481
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Other names
LM3481MMTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3481MM/NOPB
Manufacturer:
TI
Quantity:
12 000
Under Voltage Lockout (UVLO) Pin
The UVLO pin provides user programmable enable and shut-
down thresholds. The UVLO pin is compared to an internal
reference of 1.43V (typical), and a resistor divider programs
the enable threshold, V
current is sourced out of the UVLO pin, which effectively
causes a hysteresis, and the UVLO shutdown threshold,
V
thresholds requires two resistors connected from the V
to the UVLO pin and from the UVLO pin to GND (see
11). Select the desired enable, V
V
determine the resistance values:
If the UVLO pin function is not desired, select R8 and R7 of
equal magnitude greater than 100 kΩ. This will allow V
be in control of the UVLO thresholds. The UVLO pin may also
be used to implement the enable/disable function. If a signal
pulls the UVLO pin below the 1.43V (typical) threshold, the
converter will be disabled.
SH
SH
, is now lower than the enable threshold. Setting these
, threshold voltages and use the following equations to
FIGURE 12. Simplified Boost Converter Diagram (a) First cycle of operation. (b) Second cycle of operation
FIGURE 11. UVLO Pin Resistor Divider
EN
. When the IC is enabled, a 5 μA
EN
, and UVLO shutdown,
20136596
Figure
IN
IN
pin
to
13
Short Circuit Protection
When the voltage across the sense resistor (measured on the
I
tivated. A comparator inside the LM3481 reduces the switch-
ing frequency by a factor of 8 and maintains this condition until
the short is removed.
Typical Applications
The LM3481 may be operated in either continuous or discon-
tinuous conduction mode. The following applications are de-
signed for continuous conduction operation. This mode of
operation has higher efficiency and lower EMI characteristics
than the discontinuous mode.
BOOST CONVERTER
The most common topology for the LM3481 is the boost or
step-up topology. The boost converter converts a low input
voltage into a higher output voltage. The basic configuration
for a boost regulator is shown in
conduction mode (when the inductor current never reaches
zero at steady state), the boost regulator operates in two cy-
cles. In the first cycle of operation, MOSFET Q is turned on
and energy is stored in the inductor. During this cycle, diode
D1 is reverse biased and load current is supplied by the output
capacitor, C
In the second cycle, MOSFET Q is off and the diode is forward
biased. The energy stored in the inductor is transferred to the
load and output capacitor. The ratio of these two cycles de-
termines the output voltage. The output voltage is defined as:
(ignoring the voltage drop across the MOSFET and the
diode), or
where D is the duty cycle of the switch, V
voltage drop of the diode, and V
FET when it is on. The following sections describe selection
of components for a boost converter.
SEN
Pin) exceeds 220 mV, short-circuit current limit gets ac-
OUT
.
Q
is the drop across the MOS-
Figure
12. In continuous
D1
20136522
is the forward
www.national.com