ISL8560IRZ Intersil, ISL8560IRZ Datasheet - Page 11

IC REG 2A DC/DC STEP-DN 20-QFN

ISL8560IRZ

Manufacturer Part Number
ISL8560IRZ
Description
IC REG 2A DC/DC STEP-DN 20-QFN
Manufacturer
Intersil
Type
Step-Down (Buck)r
Datasheet

Specifications of ISL8560IRZ

Internal Switch(s)
Yes
Synchronous Rectifier
Yes
Number Of Outputs
1
Voltage - Output
1.21 ~ 55 V
Current - Output
2A
Frequency - Switching
100kHz ~ 600kHz
Voltage - Input
9 ~ 60 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-VQFN Exposed Pad, 20-HVQFN, 20-SQFN, 20-DHVQFN
Power - Output
3W
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL8560IRZ
Manufacturer:
Intersil
Quantity:
48
Part Number:
ISL8560IRZ
Manufacturer:
Intersil
Quantity:
135
Typical Performance Curves
Applications Information
Product Description
The ISL8560 is a non-synchronous, integrated FET 2A step
down regulator which operates from an unregulated input of
9V to 60V. The output voltage is user-adjustable with a pair
of external resistors. Frequency of operation is adjustable
from 100kHz to 600kHz set by RTCT. An external signal with
higher frequency can be injected to SYNCH to synchronize
the controller.
The buck controller drives an internal N-Channel MOSFET
and requires an external diode to deliver load current up to
2A. A Schottky diode is recommended for improved
efficiency and performance over a standard diode. The
converter output is regulated down to 1.21V from an input
source.
The PWM control loop uses a single output voltage loop with
input voltage feed forward which simplifies feedback loop
compensation and rejects input voltage variation. External
feedback loop compensation allows flexibility in output filter
component selection.
The buck regulator is equipped with a lossless current limit
scheme. The current limit in the buck regulator is achieved by
monitoring the drain-to-source current of the internal switching
power MOSFET. The current limit threshold is internally set at
4.5A peak. Additional features include programable soft-start to
support proper start-up of wide output capacitance range.
Start-Up and Shut-Down
When the EN pin is connected to a logic high, the ISL8560 is
in the shut-down mode. All the control circuitry and both
MOSFETs are off, and V
total input current is less than 110µA.
When the EN pin is tied to GND, and V
approximately 9V, the regulator begins to switch. The output
OUT
11
falls to zero. In this mode, the
IN
(Continued)
reaches
FIGURE 28. OUTPUT SHORT CIRCUIT
ISL8560
voltage is gradually increased to ensure proper soft-start
operation.
When the EN reaches logic LOW, the regulator repeats the
start-up procedure, including the soft-start function. Connect
a capacitor from SS pin to ground. This capacitor, along with
an internal 10µA current source sets the soft-start interval of
the converter, t
Operating Frequency
The ISL8560 can operate at switching frequencies from
100kHz to 600kHz. A resistor tied from the RTCT pin to VIN
and a capacitor from RTCT to GND are used to program the
switching frequency through Equation 2.
Caution: When the ISL8560 is in disabled state, the voltage
across RTCT pin will reach V
voltage rating of the RTCT capacitor is rated as high as the
input voltage.
Output Voltage Selection
The output voltage of the regulator can be programmed via
an external resistor divider that is used to scale the output
voltage relative to the internal reference voltage and feed it
back to the inverting input of the error amplifier. Refer to
Figure 30.
The output voltage programming resistor, R
the value chosen for the feedback resistor and the desired
output voltage of the regulator. The value for the feedback
resistor is typically between 1kΩ and 10kΩ.
If the output voltage desired is 1.21V, then R
unpopulated.
C
C
R
SS
1
3
[
nF
=
[
μF
------------------------------------- -
V
]
R
OUT
]
=
2
PGOOD = 5V/DIV
---------------- -
R kΩ
×
8.3 t
6.25
V
[
1.21V
OUT
LX = 10V/DIV
1.21V
IL = 2A/DIV
SS
]
SS
= 2V/DIV
----------------------------- - 0.3
f
.
OSC
s [ ]
1000
[
kHz
]
IN
voltage. Make sure that the
3
, will depend on
3
is left
September 19, 2008
(EQ. 1)
FN9244.7
(EQ. 3)
(EQ. 2)

Related parts for ISL8560IRZ