NCP3102MNTXG ON Semiconductor, NCP3102MNTXG Datasheet - Page 6

• Manufacturer Part Number: NCP3102MNTXG
• Description: IC CONV SYNC BUCK 10A 40QFN
• Manufacturer: ON Semiconductor
• Type: Step-Down (Buck)r

Specifications of NCP3102MNTXG

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: Adj to 0.8V
• Current - Output: 10A
• Frequency - Switching: 275kHz
• Voltage - Input: 4.5 ~ 13.2 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 40-TQFN Exposed Pad
• Power - Output: 3W
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: NCP3102MNTXGOSTR

General
voltage 10 A synchronous PWM buck converter designed to
operate from a 5 V to 13.2 V supply. The output voltage of
the converter can be precisely regulated down to 800 mV
$1.0% when the V
frequency is internally set to 275 kHz. A high gain
Operational Transconductance Error Amplifier (OTA) is
used for feedback and stabilizing the loop.
Duty Cycle and Maximum Pulse Width Limits
at an operating point defined by the ratio of the input to the
output voltage. The NCP3102 can achieve an 80% duty
cycle. There is a built in off-time which ensures that the
bootstrap supply is charged every cycle. The NCP3102,
which is capable of a 100 nsec pulse width (minimum), can
allow a 12 V to 0.8 V conversion at 275 kHz. The duty cycle
limit and the corresponding output voltage are shown below
in graphical format in Figure 10 and 12. The light gray area
represents the safe operating area for the lowest maximum
operational duty cycle and the dark grey area represents the
absolute maximum duty cycle and corresponding output
voltage.
Input Voltage Range (V
13.2 V with reference to GND and PHS, respectively.
Although BST is rated at 13.2 V with reference to PHS, it can
also tolerate 25 V with respect to GND.
NCP3102 is a high efficiency integrated wide input
In steady state DC operation, the duty cycle will stabilize
The input voltage range for both V
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0.8
Max-Maximum
Min-Maximum
Figure 10. Duty Cycle to Output Voltage
4.5 V
2.8
FB
OUTPUT VOLTAGE (V)
pin is tied to V
CC
4.8
and BST)
13.2 V
CC
6.8
DETAILED OPERATING DESCRIPTION
OUT
and BST is 4.5 V to
. The switching
Minimum
8.8
http://onsemi.com
10.8
NCP3102
6
External Enable/Disable
below the 400 mV threshold as shown in Figure 12, it
disables the PWM Logic and the gate drive outputs. In this
disabled
amplifier's (EOTA) output source current is reduced and
limited to the Soft-Start mode of 10 mA. Always start
normal operation condition after disable mode begins by
soft-start sequence. This is mentioned in the next section.
Normal Shutdown Behavior
because the input supply reaches UVLO threshold. In this
case, switching stops, the internal soft-start, SS, is
discharged, and all GATE pins go low. The switch node
enters a high impedance state and the output capacitors
When the Comp Pin voltage falls or is pulled externally
Normal shutdown occurs when the IC stops switching
10
9
8
7
6
5
4
3
Figure 11. Maximum Input to Output Voltage
4.5
mode,
5.5
Figure 12. Disable Circuit
6.5
D
COMP/DIS
MAX
the
7.5
INPUT VOLTAGE (V)
= 0.8
FB
operational
D
8.5
MAX
17
16
= 0.7
9.5
V
0.8 V
-
+
REF
10.5 11.5 12.5 13.5
transconductance