MAX1044CSA+ Maxim Integrated Products, MAX1044CSA+ Datasheet - Page 5

• Manufacturer Part Number: MAX1044CSA+
• Description: IC MULTI CONFIG 20MA 8SOIC
• Manufacturer: Maxim Integrated Products
• Type: Switched Capacitor (Charge Pump), Divider, Doubler, Invertingr

Specifications of MAX1044CSA+

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Current - Output: 20mA
• Frequency - Switching: 10kHz
• Voltage - Input: 1.5 ~ 10 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Power - Output: 471mW
• Output Voltage: - 1.5 V to - 10 V or 3 V to 20 V
• Output Current: 20 mA
• Input Voltage: 1.5 V to 10 V
• Supply Current: 80 uA
• Switching Frequency: 5 KHz
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The MAX1044/ICL7660 are charge-pump voltage con-
verters. They work by first accumulating charge in a
bucket capacitor and then transfer it into a reservoir
capacitor. The ideal voltage inverter circuit in Figure 2
illustrates this operation.
Figure 1. Maxim MAX1044/ICL7660 Test Circuit
_______________Detailed Description
_____________________________________________________________ Pin Description
PIN
1
2
3
4
5
6
7
8
10 F
C1
(MAX1044)
(ICL7660)
BOOST
CAP+
GND
CAP-
BOOST
NAME
CAP+
CAP-
V
GND
N.C.
OSC
V+
OUT
LV
MAX1044
ICL7660
_______________________________________________________________________________________
Switched-Capacitor Voltage Converters
Frequency Boost. Connecting BOOST to V+ increases the oscillator frequency by a factor of six. When the
oscillator is driven externally, BOOST has no effect and should be left open.
No Connection
Connection to positive terminal of Charge-Pump Capacitor
Ground. For most applications, the positive terminal of the reservoir capacitor is connected to this pin.
Connection to negative terminal of Charge-Pump Capacitor
Negative Voltage Output. For most applications, the negative terminal of the reservoir capacitor is
connected to this pin.
Low-Voltage Operation. Connect to ground for supply voltages below 3.5V.
ICL7660: Leave open for supply voltages above 5V.
Oscillator Control Input. Connecting an external capacitor reduces the oscillator frequency. Minimize stray
capacitance at this pin.
Power-Supply Positive Voltage Input. (1.5V to 10V). V+ is also the substrate connection.
V
OSC
OUT
V+
LV
C
= 0.1µF
10 F
BYPASS
C2
EXTERNAL
OSCILLATOR
C
OSC
R
L
V+
V
OUT
During the first half of each cycle, switches S1 & S3
close and switches S2 & S4 open, which connects the
bucket capacitor C1 across V+ and charges C1.
During the second half of each cycle, switches S2 & S4
close and switches S1 & S3 open, which connects the
positive terminal of C1 to ground and shifts the nega-
tive terminal to V
the reservoir capacitor C2. If the voltage across C2 is
smaller than the voltage across C1, then charge flows
from C1 to C2 until the voltages across them are equal.
During successive cycles, C1 will continue pouring
charge into C2 until the voltage across C2 reaches
- (V+). In an actual voltage inverter, the output is less
than - (V+) since the switches S1–S4 have resistance
and the load drains charge from C2.
Additional qualities of the MAX1044/ICL7660 can be
understood by using a switched-capacitor circuit
model. Switching the bucket capacitor, C1, between
the input and output of the circuit synthesizes a resis-
tance (Figures 3a and 3b.)
When the switch in Figure 3a is in the left position,
capacitor C1 charges to V+. When the switch moves to
the right position, C1 is discharged to V
charge transferred per cycle is: ∆Q = C1(V+ - V
the switch is cycled at frequency f, then the resulting
FUNCTION
OUT
. This connects C1 in parallel with
OUT
OUT
. The
). If
5