MAX1653EEE Maxim Integrated Products, MAX1653EEE Datasheet - Page 19

• Manufacturer Part Number: MAX1653EEE
• Description: IC CTRLR DCDC PWM STPDWN 16-QSOP
• Manufacturer: Maxim Integrated Products
• Type: Step-Down (Buck)r

Specifications of MAX1653EEE

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 2.5 ~ 5.5 V
• Current - Output: 10A
• Frequency - Switching: 150kHz, 300kHz
• Voltage - Input: 4.5 ~ 30 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Power - Output: 667mW
• Output Voltage: 2.5 V to 5.5 V
• Output Current: 10 A
• Input Voltage: 4.5 V to 30 V
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

output voltage as determined by the turns ratio is +15V,
the feedback resistor ratio should be set to produce
about +13.5V; otherwise, the SECFB one-shot might be
triggered unintentionally, causing an unnecessary
increase in supply current and output noise. In negative-
output (MAX1654) applications, the resistor-divider acts
as a load on the internal reference, which in turn can
cause errors at the main output. Avoid overloading REF
(see the Reference Load-Regulation Error vs. Load
Current graph in the Typical Operating Characteristics ).
100kΩ is a good value for R3 in MAX1654 circuits.
Output current on secondary winding applications is
limited at low input voltages. See the MAX1652
Maximum Secondary Output Current vs. Supply Voltage
graph in the Typical Operating Characteristics for data
from the application circuit of Figure 8.
Soft-start allows a gradual increase of the internal cur-
rent-limit level at start-up for the purpose of reducing
Figure 8. 5V/15V Dual-Output Application Circuit (MAX1652)
(OPTIONAL)
ON/OFF
0.01 F
22 F, 35V
22 F, 35V
6
1
4
GND
SHDN
SS
SECFB
2
SYNC
5
______________________________________________________________________________________
MAX1652
7
FB
3
REF
Soft-Start Circuit (SS)
11
VL
0.33 F
PGND
CSH
CSL
BST
DH
DL
V+
LX
DC-DC Controllers in 16-Pin QSOP
4.7 F
16
14
15
13
12
8
9
10
High-Efficiency, PWM, Step-Down
C2
4700pF*
Si9410
Si9410
0.1 F
D1
CMPSH
-3A
V
IN
(6.5V TO 18V)
22 *
EC11FS1
C2
4.7 F
input surge currents, and perhaps for power-supply
sequencing. In shutdown mode, the soft-start circuit
holds the SS capacitor discharged to ground. When
SHDN goes high, a 4µA current source charges the SS
capacitor up to 3.2V. The resulting linear ramp wave-
form causes the internal current-limit level to increase
proportionally from 0 to 100mV. The main output capaci-
tor thus charges up relatively slowly, depending on the
SS capacitor value. The exact time of the output rise
depends on output capacitance and load current and is
typically 1ms per nanofarad of soft-start capacitance.
With no SS capacitor connected, maximum current limit
is reached within 10µs.
Shutdown mode (SHDN = 0V) reduces the V+ supply
current to typically 3µA. In this mode, the reference and
VL are inactive. SHDN is a logic-level input, but it can
be safely driven to the full V+ range. Connect SHDN to
V+ for automatic start-up. Do not allow slow transitions
(slower than 0.02V/µs) on SHDN.
D2
1N5819
T1 = TRANSPOWER TTI5870
* = OPTIONAL, MAY NOT BE NEEDED
15 H
2.2:1
T1
C3
15 F
2.5V
0.01 F
210k, 1%
20m
49.9k, 1%
220 F
10V
1/4 W
18V
Shutdown
+15V AT
250mA
+5V
AT 3A
220 F
10V
19