MAX1653EEE Maxim Integrated Products, MAX1653EEE Datasheet - Page 9

• Manufacturer Part Number: MAX1653EEE
• Description: IC CTRLR DCDC PWM STPDWN 16-QSOP
• Manufacturer: Maxim Integrated Products
• Type: Step-Down (Buck)r

Specifications of MAX1653EEE

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 2.5 ~ 5.5 V
• Current - Output: 10A
• Frequency - Switching: 150kHz, 300kHz
• Voltage - Input: 4.5 ~ 30 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Power - Output: 667mW
• Output Voltage: 2.5 V to 5.5 V
• Output Current: 10 A
• Input Voltage: 4.5 V to 30 V
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Dual Mode is a trademark of Maxim Integrated Products.
PIN
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
(MAX1652/
(MAX1653/
MAX1654)
MAX1655)
SECFB
NAME
SHDN
PGND
SYNC
GND
SKIP
CSH
REF
CSL
BST
DH
FB
V+
DL
SS
VL
LX
_______________________________________________________________________________________
Soft-Start Timing Capacitor Connection. Ramp time to full current limit is approximately 1ms/nF.
Secondary Winding Feedback Input. Normally connected to a resistor divider from an auxiliary output.
Don’t leave SECFB unconnected.
Disables pulse-skipping mode when high. Connect to GND for normal use. Don’t leave SKIP unconnected.
With SKIP grounded, the device will automatically change from pulse-skipping operation to full PWM opera-
tion when the load current exceeds approximately 30% of maximum (Table 3).
Reference Voltage Output. Bypass to GND with 0.33µF minimum.
Low-Noise Analog Ground and Feedback Reference Point
Oscillator Synchronization and Frequency Select. Tie to GND or VL for 150kHz operation; tie to REF for
300kHz operation. A high-to-low transition begins a new cycle. Drive SYNC with 0 to 5V logic levels (see the
Electrical Characteristics table for V
Shutdown Control Input, active low. Logic threshold is set at approximately 1V (V
MOSFET). Tie SHDN to V+ for automatic start-up.
Feedback Input. Regulates at the feedback voltage in adjustable mode. FB is a Dual Mode
selects the fixed output voltage settings as follows:
Current-Sense Input, high side. Current-limit level is 100mV referred to CSL.
Current-Sense Input, low side. Also serves as the feedback input in fixed-output modes.
Battery Voltage Input (4.5V to 30V). Bypass V+ to PGND close to the IC with a 0.1µF capacitor. Connects to a
linear regulator that powers VL.
5V Internal Linear-Regulator Output. VL is also the supply voltage rail for the chip. VL is switched to the out-
put voltage via CSL (V
to 5mA for external loads.
Power Ground
Low-Side Gate-Drive Output. Normally drives the synchronous-rectifier MOSFET. Swings from 0V to VL.
Boost Capacitor Connection for High-Side Gate Drive (0.1µF)
Switching Node (inductor) Connection. Can swing 2V below ground without hazard.
High-Side Gate-Drive Output. Normally drives the main buck switch. DH is a floating driver output that swings
from LX to BST, riding on the LX switching-node voltage.
MAX1652: SECFB regulates at VSECFB = 2.50V. Tie to VL if not used.
MAX1654: SECFB regulates at VSECFB = 0V. Tie to a negative voltage through a high-value current-
limiting resistor (I
Connect to GND for 3.3V operation.
Connect to VL for 5V operation.
Connect FB to a resistor divider for adjustable mode. FB can be driven with +5V CMOS logic in order to
change the output voltage under system control.
DC-DC Controllers in 16-Pin QSOP
High-Efficiency, PWM, Step-Down
MAX
CSL
= 100µA) if not used.
> 4.5V) for automatic bootstrapping. Bypass to GND with 4.7µF. VL can supply up
IH
and V
IL
specifications). SYNC capture range is 190kHz to 340kHz.
FUNCTION
TH
Pin Description
of an internal N-channel
TM
input that also
9