HCPL-053L-000E Avago Technologies US Inc., HCPL-053L-000E Datasheet - Page 10

• Manufacturer Part Number: HCPL-053L-000E
• Description: OPTOCOUPLER 1MBD 3.3V 8-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-053L-000E

• Input Type: DC
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 8mA
• Data Rate: 1Mbps
• Propagation Delay High - Low @ If: 350ns @ 16mA
• Current - Dc Forward (if): 25mA
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 8 mA
• Maximum Forward Diode Current: 25 mA
• Output Device: Transistor With Base
• Configuration: 2 Channel
• Current Transfer Ratio: 50 %
• Maximum Baud Rate: 1 MBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 50 mA
• Maximum Power Dissipation: 100 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: 0 C
• Number Of Elements: 2
• Reverse Breakdown Voltage: 5V
• Forward Voltage: 1.7V
• Forward Current: 50mA
• Package Type: SOIC
• Collector Current (dc) (max): 8mA
• Power Dissipation: 100mW
• Pin Count: 8
• Mounting: Surface Mount
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1632-5

Package Characteristics
Over Recommended Temperature (T
Parameter
Input-Output
Momentary
Withstand
Voltage**
Input-Output
Resistance
Input-Output
Capacitance
*All typicals at T
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable),
your equipment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage," publica-
tion number 5963-2203E.
Notes:
10. The frequency at which the AC output voltage is 3 dB below its mid-frequency value.
11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 15%.
12. See Option 020 data sheet for more information.
13. Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended.
14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage
15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage
16. This rating is equally validated by an equivalent AC proof test.
10
1. Derate linearly above 70˚C free-air temperature at a rate of 0.8 mA/˚C (8-Pin DIP).
2. Derate linearly above 70˚C free-air temperature at a rate of 1.6 mA/˚C (8-Pin DIP).
3. Derate linearly above 70˚C free-air temperature at a rate of 0.9 mW/˚C (8-Pin DIP).
4. Derate linearly above 70˚C free-air temperature at a rate of 2.0 mW/˚C (8-Pin DIP).
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I
6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
8. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 mA kΩ pull-up resistor.
9. The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1 kΩ pull-up resistor.
Derate linearly above 85˚C free-air temperature at a rate of 0.5 mA/˚C (SO-8).
Derate linearly above 85˚C free-air temperature at a rate of 1.0 mA/˚C (SO-8).
Derate linearly above 85˚C free-air temperature at a rate of 1.1 mW/˚C (SO-8).
Derate linearly above 85˚C free-air temperature at a rate of 2.3 mW/˚C (SO-8).
mon mode pulse signal, V
munity in a Logic Low level is the maximum tolerable (negative) dV
assure that the output will remain in a Logic Low state (i.e., V
detection current limit, I
tion Related Characteristics Table, if applicable.
detection current limit, I
tion Related Characteristics Table, if applicable.
A
= 25˚C.
Sym.
V
I
R
C
I-O
I-O
ISO
I-O
I-O
I-O
CM
Device
8-Pin DIP
SO-8
8-Pin DIP
8-Pin DIP
SO-8
8-Pin DIP
SO-8
≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insula-
≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insula-
, to assure that the output will remain in a Logic High state (i.e., V
A
= 0˚C to 70˚C) unless otherwise specified.
Min.
3750
O
Typ.*
10
0.6
< 0.8 V).
12
CM
Max.
1
/dt on the trailing edge of the common mode pulse signal, V
Units
V rms
µA
Ω
pF
O
, to the forward LED input current, I
Test Conditions
RH < 50%,
t = 1 min.,
T
45% RH, t = 5 s,
V
T
V
f = 1 MHz
A
A
I-O
I-O
O
= 25˚C
= 25˚C
> 2.0 V). Common mode transient im-
CM
= 3 kVdc,
= 500 Vdc
/dt on the leading edge of the com-
Fig.
F
, times 100.
CM
Note
6, 14
6, 16
6
6
, to