6N138 Avago Technologies US Inc., 6N138 Datasheet - Page 12

OPTOCOUPLER DARL-OUT 8-DIP

6N138

Manufacturer Part Number
6N138
Description
OPTOCOUPLER DARL-OUT 8-DIP
Manufacturer
Avago Technologies US Inc.
Datasheets

Specifications of 6N138

Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
60mA
Data Rate
100KBd
Propagation Delay High - Low @ If
5µs @ 500µA
Current - Dc Forward (if)
12mA
Input Type
DC
Output Type
Open Collector
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
No. Of Channels
1
Optocoupler Output Type
Photodarlington
Input Current
12mA
Output Voltage
7V
Opto Case Style
DIP
No. Of Pins
8
Ctr Max
2600%
Isolation Voltage
3.75kV
Output Device
Darlington With Base
Number Of Elements
1
Reverse Breakdown Voltage
5V
Forward Voltage
1.7V
Forward Current
20mA
Package Type
PDIP
Collector Current (dc) (max)
60mA
Power Dissipation
135mW
Current Transfer Ratio
2600%
Pin Count
8
Mounting
Through Hole
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant, Contains lead / RoHS non-compliant
Other names
516-1007-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
6N138
Manufacturer:
FSC
Quantity:
967
Part Number:
6N138
Manufacturer:
QTC
Quantity:
112
Part Number:
6N138
Manufacturer:
INTEL
Quantity:
81
Part Number:
6N138
Manufacturer:
AVAGO
Quantity:
20 000
Company:
Part Number:
6N138
Quantity:
1 000
Part Number:
6N138-000E
Manufacturer:
AVG
Quantity:
250
Part Number:
6N138-000E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
6N138-020E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
6N138-300E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
6N138-500E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Company:
Part Number:
6N138-X009
Quantity:
70 000
Company:
Part Number:
6N138M
Quantity:
40 000
Part Number:
6N138S
Manufacturer:
FSC
Quantity:
2 000
Company:
Part Number:
6N138SDM
Quantity:
158 000
Package Characteristics
**All typicals at T
†The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating.
For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level safety
specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage. ”
Notes:
1. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I
2. Pin 7 Open.
3. Device considered a two-terminal device. Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
4. Use of a resistor between pin 5 and 7 will decrease gain and delay time. Significant reduction in overall gain can occur when using resistor values
5. Common mode transient immunity in a Logic High level is the maximum toler able (positive) dV
6. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, R
7. Use of a 0.1 µF bypass capacitor connected between pins 8 and 5 adjacent to the device is recommended.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 4500 V rms for 1 second (leakage detection
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detection
12
Parameter
Input-Output Momentary
Withstand Voltage†
Resistance (Input-Output)
Capacitance (Input-Output)
below 47 kΩ. For more information, please contact your local Avago Components representative.
that the output will remain in a Logic High state (i.e., V
(negative) dV
detector IC from destructively high surge currents. The recommended value is R
current limit, I
acteristics Table, if applicable.
current limit, I
60747-5-2 Insulation Related Characteristics Table, if applicable.
CM
I-O
A
I-O
= 25°C, unless otherwise noted.
/dt of the common mode pulse, V
< 5 µA). This test is per formed before the 100% production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Char-
< 5 µA). This test is per formed before the 100% production test for partial discharge (method b) shown in the IEC/EN/DIN EN
Option 020
HCNW139
HCNW138
Sym.
V
R
C
ISO
I-O
I-O
CM
, to assure that the output will remain in a Logic Low state (i.e., V
3750
5000
Min.
O
> 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable
Typ.**
10
0.6
12
Max.
CC
= 220 Ω.
V rms
Units
pF
Ω
O
, to the forward LED input current, I
RH < 50%, t = 1 min.,
T
V
RH < 45%
f = 1 MHz
A
I-O
CM
= 25°C
= 500 Vdc
/dt of the common mode pulse, V
Test Conditions
CC
, should be included to protect the
O
< 0.8 V).
F
, times 100%.
Fig.
CM
, to assure
Note
3, 8
3, 9
3
3

Related parts for 6N138