ACPL-K453-520E Avago Technologies US Inc., ACPL-K453-520E Datasheet - Page 6
![OPTOCOUPLER 1CH HIGH SPD 8-SOIC](/photos/26/82/268206/acpl-k453_wht_sml.jpg)
ACPL-K453-520E
Manufacturer Part Number
ACPL-K453-520E
Description
OPTOCOUPLER 1CH HIGH SPD 8-SOIC
Manufacturer
Avago Technologies US Inc.
Specifications of ACPL-K453-520E
Package / Case
SO-8
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
8mA
Data Rate
1Mbps
Propagation Delay High - Low @ If
200ns @ 16mA
Current - Dc Forward (if)
25mA
Input Type
DC
Output Type
Open Collector
Mounting Type
Surface Mount, Gull Wing
Isolation Voltage
3750 Vrms
Output Device
Integrated Photo IC
Configuration
1 Channel
Current Transfer Ratio
24 %
Maximum Baud Rate
1 MBps
Maximum Forward Diode Voltage
1.7 V
Maximum Reverse Diode Voltage
5 V
Maximum Power Dissipation
100 mW
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Switching Specifications
Over recommended temperature (T
*
Package Characteristics
Over recommended temperature (T
*
Notes:
1. Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C.
2. Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C.
3. Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C.
4. Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C.
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I
6. Device considered a two terminal device: pins 2 and 3 shorted together, and pins 5, 6, 7 and 8 shorted together.
7. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V
8. Common transient immunity in a Logic High level is the maximum tolerable (positive) dV
9. The 1.9 kW load represents 1 TTL unit load of 1.6 mA and the 5.6 kW pull-up resistor.
10. Use of a 0.1 mF bypass capacitor connected between pins 4 and 6 is recommended.
6
Parameter
Propagation Delay Time
to Logic Low at Output
Propagation Delay Time
to Logic High at Output
Common Mode Transient
Immunity at Logic High
Level Output
Common Mode Transient
Immunity at Logic Low
Level Output
Parameter
Input-Output Momentary
Withstand Voltage*
Input-Output Resistance
Input-Output Capacitance
All typicals at T
The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable).
current limit, I
detection current limit, I
to assure that the output will remain in a Logic High state (i.e., V
tolerable (negative) dV
(i.e., V
O
< 0.8 V).
I-O
A
= 25°C.
≤ 5 µA); optocoupler with option 020 is proof tested by applying an insulation test voltage ≥ 6000 V
CM
I-O
/dt on the falling edge of the common mode pulse signal, V
≤ 5 mA).
Symbol
t
t
|CM
|CM
PHL
PLH
H
L
Symbol
V
R
C
|
|
ISO
I-O
I-O
A
A
= 0°C to 70°C) V
Min.
15
15
= 0°C to 70°C) unless otherwise specified. All typicals at T
Min.
3750
5000 (For Option 020)
Typ.*
0.2
0.6
30
30
Typ.
10
0.6
Max.
0.8
1.0
0.8
1.0
CC
12
O
> 2.0 V). Common mode transient immunity in a Logic Low level is the maximum
= 5 V, I
Units
ms
kV/ms
Max.
F
= 16 mA unless otherwise specified.
Test Conditions
T
T
V
V
A
A
CM
CM
Units
Vrms
W
pF
= 25°C
= 25°C
CM
=1500 V
=1500 V
CM
O
to assure that the output will remain in a Logic Low state
, to the forward LED input current, I
/dt on the rising edge of the common mode pulse, V
Test Conditions
RH ≤ 50%, t = 1 min;
T
V
f = 1 MHz; V
p-p
p-p
A
I-O
= 25°C
= 500 Vdc
R
C
R
C
I
R
C
I
R
C
F
F
L
L
L
L
L
L
L
L
= 0 mA, T
= 16 mA, T
= 1.9 kW,
= 1.9 kW,
= 1.9 kW,
= 1.9 kW,
= 15 pF
= 15 pF
= 15 pF
= 15 pF
I-O
RMS
= 0 Vdc
for 1 second (leakage detection
A
A
A
= 25°C
= 25°C.
= 25°C
RMS
Fig.
for 1 second (leakage
F
, times 100.
Fig.
5,6,9
5,6,9
10
10
Note
6,7
6
6
Note
9
9
8,9
8,9
CM
,