ACPL-T350-000E Avago Technologies US Inc., ACPL-T350-000E Datasheet - Page 8

• Manufacturer Part Number: ACPL-T350-000E
• Description: OPTOCOUPLER 2.5A IGBT 8-DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of ACPL-T350-000E

• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 2.5A
• Propagation Delay High - Low @ If: 250ns @ 7mA ~ 16mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• No. Of Channels: 1
• Optocoupler Output Type: Gate Drive
• Input Current: 16mA
• Output Voltage: 30V
• Opto Case Style: DIP
• No. Of Pins: 8
• Input Current Max: 230mA
• Isolation Voltage: 3.75kV
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 7. Package Characteristics
Over recommended temperature (T
** The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.3 mA /°C.
2. Maximum pulse width = 10 µs.
3. Derate linearly above 70° C free-air temperature at a rate of 4.8 mW /°C.
4. Derate linearly above 70° C free-air temperature at a rate of 5.4 mW /°C. The maximum LED junction temperature should not exceed 125°C.
5. Maximum pulse width = 50 µs
6. In this test VOH is measured with a dc load current. When driving capacitive loads VOH will approach V
7. Maximum pulse width = 1 ms
8. This load condition approximates the gate load of a 1200 V/100A IGBT.
9. Pulse Width Distortion (PWD) is defined as |t
10. The difference between t
11. Pins 1 and 4 need to be connected to LED common.
12. Common mode transient immunity in the high state is the maximum tolerable dV
13. Common mode transient immunity in a low state is the maximum tolerable dVCM/dt of the common mode pulse, V
14. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage detection
15. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
8
Parameter
Input-Output Momentary Withstand Voltage**
Resistance Input-Output)
Capacitance Input-Output)
LED-to-Case Thermal Resistance
LED-to-Detector Thermal Resistance
Detector-to-Case Thermal Resistance
voltage rating. For the continuous voltage rating refers to your equipment level safety specification or Avago Application Note 1074 entitled
“Optocoupler Input-Output Endurance Voltage. ”
output will remain in the high state (i.e., V
will remain in a low state (i.e., V
current limit, I
I-O
≤ 5 µA).
PHL
and t
O
< 2.0 V).
PLH
between any two ACPL-T350 parts under the same test condition.
A
O
= -40 to 100°C) unless otherwise specified. All typicals at T
> 15.0 V).
PHL
Symbol Min.
V
R
C
q
q
q
- t
I-O
ISO
I-O
LC
LD
DC
PLH
| for any given device.
3750
Typ.
10
0.6
67
2
126
12
Max.
CM
Units
Vrms
W
pF
°C/W
°C/W
°C/W
/dt of the common mode pulse, V
Test Conditions
RH < 50%,
t = 1 min.,
T
V
Freq=1 MHz
Thermocouple located at
center underside of package
A
I-O
= 25°C
= 500 V
CC
as I
OH
approaches zero amps.
A
CM
= 25°C.
, to assure that the output
CM
, to assure that the
Fig.
Note
1, 15
15