ACPL-P454-560E Avago Technologies US Inc., ACPL-P454-560E Datasheet - Page 9
![OPTOCOUPLER 1MBD VDE 6-SOIC](/photos/26/82/268208/acpl-p456_wht_sml.jpg)
ACPL-P454-560E
Manufacturer Part Number
ACPL-P454-560E
Description
OPTOCOUPLER 1MBD VDE 6-SOIC
Manufacturer
Avago Technologies US Inc.
Specifications of ACPL-P454-560E
Input Type
DC
Package / Case
SO-6
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
8mA
Propagation Delay High - Low @ If
200ns @ 16mA
Current - Dc Forward (if)
25mA
Output Type
Open Collector
Mounting Type
Surface Mount
Isolation Voltage
3750 Vrms
Output Device
Phototransistor
Configuration
1 Channel
Current Transfer Ratio
37 %
Maximum Forward Diode Voltage
1.7 V
Maximum Reverse Diode Voltage
5 V
Maximum Input Diode Current
25 mA
Maximum Power Dissipation
100 mW
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Package Characteristics
Over recommended temperature (T
*
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C.
2. Derate linearly above 70°C free-air temperature at a rate of 1.6mA/°C.
3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C.
4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C.
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current (I
6. Device considered a two-terminal device: Pins 1 and 3 shorted together and Pins 4, 5 and 6 shorted together.
7. Under TTL load and drive conditions: Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
8. Under IPM (Intelligent Power Module) load and LED drive conditions: Common mode transient immunity in a Logic High level is the maximum
9. The 1.9 kW load represents 1 TTL unit load of 1.6 mA and the 5.6 kW pull-up resistor.
10. The R
11. Use of a 0.1 µF bypass capacitor connected between pins 4 and 6 is recommended.
12. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V
13. The difference between t
Figure 1. DC and Pulsed Transfer Characteristics.
Parameter
Input-Output Momentary
Withstand Voltage*
Input-Output Resistance
Input-Output Capacitance
10
The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable).
leading edge of the common mode pulse, V
immunity in a Logic Low level is the maximum tolerable (negative) dV
that the output will remain in a Logic Low state (i.e., VO < 0.8 V).
tolerable dV
V). Common mode transient immunity in a Logic Low level is the maximum tolerable dV
signal,V
current limit, I
detection current limit, I
Propagation Delay Specifications section).
5
0
0
T = 25 ˚C
V
A
CC
L
= 5.0 V
= 20 kW, C
CM
V
O
, to assure that the output will remain in a Logic Low state (i.e., V
CM
- OUTPUT VOLTAGE - V
I-O
/dt on the leading edge of the common mode pulse, VCM, to assure that the output will remain in a Logic High state (i.e., V
≤ 5 µA); each optocoupler with option 020 is proof tested by applying an insulation test voltage ≥ 6000 V
L
= 100 pF load represents an IPM (Intelligent Power Mode) load.
10
I-O
PLH
≤ 5 µA).
and t
I = 5 mA
40 mA
35 mA
30 mA
25 mA
20 mA
15 mA
10 mA
F
Symbol
V
R
C
PHL
I-O
ISO
I-O
20
, between any two ACPL-W454/P454 parts under the same test condition. (See Power Inverter Dead Time and
A
= 0°C to 70°C) unless otherwise specified. All typicals at T
CM
Min.
3750
5000 (For Option 020)
, to assure that the output will remain in a Logic High state (i.e., V
Figure . Current Transfer Ratio vs. Input Current.
1.5
1.0
0.5
0.0
0
Typ.
10
0.6
2 4 6 8 10 12 14 16 18
12
I
F
- INPUT CURRENT - mA
Max.
CM
/dt on the trailing edge of the common mode pulse signal, V
O
NORMALIZED
I
V
V
T
F
< 1.0 V).
CC
Units
Vrms
W
pF
O
A
= 16 mA
= 25 ˚C
= 0.4 V
= 5.0 V
20 22 24 26
O
Test Conditions
RH ≤ 50%, t = 1 min, T
V
f = 1 MHz; V
CM
), to the forward LED input current (I
I-O
/dt on the trailing edge of the common mode pulse
= 500 Vdc
Figure . Input Current vs. Forward Voltage.
0.001
1000
0.01
100
I-O
1.0
0.1
10
1.1
= 0 Vdc
RMS
O
1.2
V
> 2.0 V). Common mode transient
F
V
A
for 1 second (leakage detection
+
- FORWARD VOLTAGE - VOLTS
-
F
A
I
= 25°C
F
= 25°C.
1.3
RMS
for 1 second (leakage
1.4
F
Fig.
), times 100.
T = 25˚C
A
CM
CM,
1.5
/dt on the
Note
6,12
6
6
to assure
O
1.6
> 3.0