ACPL-K453-500E Avago Technologies US Inc., ACPL-K453-500E Datasheet - Page 6

• Manufacturer Part Number: ACPL-K453-500E
• Description: OPTOCOUPLER 1CH 1MBS 8-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of ACPL-K453-500E

• Input Type: DC
• Package / Case: SO-8
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 8mA
• Data Rate: 1Mbps
• Propagation Delay High - Low @ If: 200ns @ 16mA
• Current - Dc Forward (if): 25mA
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Output Device: Phototransistor
• Configuration: 1 Channel
• Current Transfer Ratio: 24 %
• Maximum Baud Rate: 1 MBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 25 mA
• Maximum Power Dissipation: 100 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Switching Specifications
Over recommended temperature (T
*
Package Characteristics
Over recommended temperature (T
*
Notes:
1. Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C.
2. Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C.
3. Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C.
4. Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C.
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I
6. Device considered a two terminal device: pins 2 and 3 shorted together, and pins 5, 6, 7 and 8 shorted together.
7. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage t 6000 V
8. Common transient immunity in a Logic High level is the maximum tolerable (positive) dV
9. The 1.9 k: load represents 1 TTL unit load of 1.6 mA and the 5.6 k: pull-up resistor.
10. Use of a 0.1 mF bypass capacitor connected between pins 4 and 6 is recommended.
6
Parameter
Propagation Delay Time
to Logic Low at Output
Propagation Delay Time
to Logic High at Output
Common Mode Transient
Immunity at Logic High
Level Output
Common Mode Transient
Immunity at Logic Low
Level Output
Parameter
Input-Output Momentary
Withstand Voltage*
Input-Output Resistance
Input-Output Capacitance
All typicals at T
The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable).
current limit, I
to assure that the output will remain in a Logic High state (i.e., V
tolerable (negative) dV
(i.e., V
O
< 0.8 V).
I-O
A
= 25°C.
d 5 PA).
CM
/dt on the falling edge of the common mode pulse signal, V
Symbol
t
t
|CM
|CM
PHL
PLH
H
L
Symbol
V
R
C
|
|
ISO
I-O
I-O
A
A
= 0°C to 70°C) V
Min.
15
15
= 0°C to 70°C) unless otherwise specified. All typicals at T
Min.
5000
Typ.*
0.2
0.6
30
30
Typ.
10
0.6
Max.
0.8
1.0
0.8
1.0
CC
12
O
> 2.0 V). Common mode transient immunity in a Logic Low level is the maximum
= 5 V, I
Units
Ps
kV/Ps
Max.
F
= 16 mA unless otherwise specified.
Test Conditions
T
T
V
V
A
A
CM
CM
Units
Vrms
:
pF
= 25°C
= 25°C
CM
=1500 V
=1500 V
CM
O
to assure that the output will remain in a Logic Low state
, to the forward LED input current, I
/dt on the rising edge of the common mode pulse, V
Test Conditions
RH d 50%, t = 1 min;
T
V
f = 1 MHz; V
p-p
p-p
A
I-O
= 25°C
= 500 Vdc
R
C
R
C
I
R
C
I
R
C
F
F
L
L
L
L
L
L
L
L
= 0 mA, T
= 16 mA, T
= 1.9 k:
= 1.9 k:
= 1.9 k:
= 1.9 k:
= 15 pF
= 15 pF
= 15 pF
= 15 pF
I-O
RMS
= 0 Vdc
for 1 second (leakage detection
A
A
A
= 25°C
= 25°C.
= 25°C
Fig.
F
, times 100.
Fig.
5,6,9
5,6,9
10
10
Note
6,7
6
6
Note
9
9
8,9
8,9
CM
,