HCPL-0710#560 Avago Technologies US Inc., HCPL-0710#560 Datasheet - Page 10

• Manufacturer Part Number: HCPL-0710#560
• Description: OPTOCOUPLER 12MBD VDE 8-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-0710#560

• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 10mA
• Data Rate: 12.5MBd
• Propagation Delay High - Low @ If: 20ns
• Input Type: Logic
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 10 mA
• Maximum Fall Time: 8 ns
• Maximum Forward Diode Current: 10 mA
• Maximum Rise Time: 9 ns
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 12.5 MBps
• Maximum Power Dissipation: 150 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Number Of Elements: 1
• Baud Rate: 12.5Mbps
• Forward Current: 10mA
• Output Current: 10mA
• Package Type: SOIC
• Operating Temp Range: -40C to 100C
• Power Dissipation: 150mW
• Propagation Delay Time: 40ns
• Pin Count: 8
• Mounting: Surface Mount
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant

10
Application Information
Bypassing and PC Board Layout
The HCPL-x710 optocouplers are extremely easy to
use. No external interface circuitry is required because
the HCPL-x710 use high-speed CMOS IC technology
allowing CMOS logic to be connected directly to the
inputs and outputs.
As shown in Figure 12, the only external components
Figure 12. Recommended Printed Circuit Board layout.
Figure 13. Recommended Printed Circuit Board layout.
Propagation Delay, Pulse-Width Distortion and Propagation Delay
Skew
Propagation Delay is a figure of merit which describes
how quickly a logic signal propagates through a
system. The propagation delay from low to high (t
is the amount of time required for an input signal to
propagate to the output, causing the output to change
Figure 14.
V
GND
INPUT
OUTPUT
V
DD1
DD1
V
V
1
I
V
I
V
O
I
GND
C1
1
10%
NC
C1, C2 = 0.01 µF TO 0.1 µF
C1
1
2
3
4
90%
HCPL-0710 fig 11
t
PLH
HCPL-0710 fig 13
t
PHL
8
7
6
5
HCPL-0710 fig 12
NC
90%
GND
50%
C2
10%
2
PLH
V
V
5 V CMOS
0 V
V
2.5 V CMOS
V
DD2
O
)
OH
OL
required for proper operation are two bypass capacitors.
Capacitor values should be between 0.01 µF and 0.1 µF.
For each capacitor, the total lead length between both
ends of the capacitor and the power-supply pins should
not exceed 20 mm. Figure 13 illustrates the recommend-
ed printed circuit board layout for the HPCL-x710.
from low to high. Similarly, the propagation delay from
high to low (t
input signal to propagate to the output, causing the
output to change from high to low. See Figure 14.
C2
C1, C2 = 0.01 µF TO 0.1 µF
PHL
) is the amount of time required for the
V
V
GND
DD2
O
2