HCPL-2531-000E Avago Technologies US Inc., HCPL-2531-000E Datasheet

Page 1

... CSA Approved IEC/EN/DIN EN 60747-5-2 –V = 630 Vpeak for HCPL-2530/2531/4534 0ption 060 IORM – 560 Vpeak for HCPL-0530/0531/0534 0ption 060 IORM • Single channel version available (4502/3, 0452/3) • MIL-PRF-38534 hermetic version available (55XX/65XX/4N55) Applications • Line receivers – high common mode transient immunity (> ...

Page 2

... Small-Outline SO-8 Single Dual Channel Channel Package* Package 6N135 HCPL-0530 6N136 HCPL-0531 HCPL-4502 HCPL-4503 HCPL-0534 Widebody (400 Mil) Hermetic Single Single Single and Channel Channel Dual Channel Package* Package* Packages* HCPL-0500 HCNW135 HCPL-0501 HCNW136 HCPL-0452 HCNW4502 HCPL-0453 HCNW4503 HCPL-55XX HCPL-65XX 4N55 ...

Page 3

... Compliant Compliant Package Mount -000E No option -300E -300 -500E -500 -020E -020 HCPL-2530 HCPL-2531 -320E -320 HCPL-4534 -520E -520 -060E -060 -360E -360 -560E -560 HCPL-0530 -000E No option HCPL-0531 -500E -500 HCPL-0534 3 Surface Gull Tape Wing & Reel 300mil X X DIP ...

Page 4

... I F2 – HCPL-4534/0534 SHIELD USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED. Package Outline Drawings 8-Pin DIP Package (HCPL-2530/2531/4534) 9.65 ± 0.25 (0.380 ± 0.010 TYPE NUMBER A XXXXZ YYWW 1 2 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± ...

Page 5

... Package Outline Drawings, continued 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2530/2531/4534) 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). ...

Page 6

Solder Reflow Thermal Profile 300 PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. 200 2.5°C ± 0.5°C/SEC. 160°C 150°C 140°C 3°C + 1°C/–0.5°C 100 PREHEATING TIME 150° SEC. ROOM TEMPERATURE Note: ...

Page 7

Insulation and Safety Related Specifications Parameter Symbol Minimum External L(101) Air Gap (External Clearance) Minimum External L(102) Tracking (External Creepage) Minimum Internal Plastic Gap (Internal Clearance) Minimum Internal Tracking (Internal Creepage) Tracking Resistance CTI (Comparative Tracking Index) Isolation Group Option ...

Page 8

... Symbol V IORM IOTM S,INPUT P S,OUTPUT R S and I on ambient temperature 125 150 175 200 Characteristic HCPL- HCPL- 2530/2531/4534 0530/0531/0534 I-IV I-IV I-III I-III I-II 55/100/21 55/100/ 630 567 1181 1050 945 840 6000 4000 175 150 230 230 600 600 9 9 > 10 > ...

Page 9

Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Average Forward Input Current (each channel) Peak Forward Input Current (each channel) (50% duty cycle pulse width) Peak Transient Input Current (each channel pulse width, 300 pps) ...

Page 10

... unless otherwise specified. See note 9. A Parameter Sym. Device Current CTR HCPL-2530/ Transfer 0530 Ratio HCPL-2531/ 0531 HCPL-4534/ 0534 Logic Low V HCPL-2530/ OL Output 0530 Voltage HCPL-2531/ 0531 HCPL-4534/ 0534 Logic High I OH Output Current Logic Low I CCL Supply Current Logic High I CCH Supply Current Input V F ...

Page 11

... Capacitance C HCPL-2530/ I-I (Input-Input) 2531/4534 HCPL-0530/ 0531/0534 *All typicals **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled “ ...

Page 12

... 0 25° – INPUT CURRENT – Figure 2. Current transfer ratio vs. input current. 2000 mA 5 HCPL-2530/0530 (R HCPL-2531/0531/4534/0534 ( 1500 1000 t t PHL PLH 500 0 -60 -20 20 100 T – TEMPERATURE – Figure 5. Propagation delay vs. temperature. 10. In accordance with UL 1577, each /dt optocoupler is proof tested by applying an ...

Page 13

T = 25° 100 , 0.20 0. – QUIESCENT INPUT CURRENT – Figure 7. Small-signal current transfer ratio vs. ...