HCPL-2531-000E Avago Technologies US Inc., HCPL-2531-000E Datasheet - Page 12

• Manufacturer Part Number: HCPL-2531-000E
• Description: OPTOCOUPLR T-OUT 2CH 1MBD 8-DIP
• Manufacturer: Avago Technologies US Inc.
• Type: Analogr

Specifications of HCPL-2531-000E

• Input Type: DC
• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 8mA
• Data Rate: 1MBd
• Propagation Delay High - Low @ If: 200ns @ 16mA
• Current - Dc Forward (if): 25mA
• Output Type: Open Collector
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 8 mA
• Maximum Forward Diode Current: 25 mA
• Output Device: Transistor With Base
• Configuration: 2 Channel
• Current Transfer Ratio: 50 %
• Maximum Baud Rate: 1 MBps
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 25 mA
• Maximum Power Dissipation: 45 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 55 C
• Package Type: 8-Pin DIP
• Special Features: 2 Channel
• No. Of Channels: 2
• Optocoupler Output Type: Phototransistor
• Input Current: 16mA
• Output Voltage: 20V
• Opto Case Style: DIP
• No. Of Pins: 8
• Ctr Max: 50%
• Ctr Min: 19%
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1474-5

Figure 1. DC and pulsed transfer
characteristics.
Figure 4. Current transfer ratio vs.
temperature.
Notes:
1. Each channel.
2. CURRENT TRANSFER RATIO is defined as
3. Device considered a two-terminal device:
4. Measured between pins 1 and 2 shorted
5. Common mode transient immunity in a
10
1.0
0.9
0.8
0.7
0.6
1.1
5
0
the ratio of output collector current, I
to the forward LED input current, I
times 100%.
pins 1, 2, 3, and 4 shorted together and
pins 5, 6, 7, and 8 shorted together.
together, and pins 3 and 4 shorted
together.
Logic High level is the maximum tolerable
(positive) dV
the common mode pulse, V
that the output will remain in a Logic High
state (i.e., V
0
-60
T = 25°C
V
A
CC
NORMALIZED
I = 16 mA
V = 0.5 V
V
T = 25°C
-40
V
F
A
O
CC
= 5.0 V
O
T
– OUTPUT VOLTAGE – V
A
= 5 V
-20
O
CM
– TEMPERATURE – °C
HCPL-2530/0530
HCPL-2531/0531/4534/0534
> 2.0 V). Common mode
/dt on the rising edge of
0
10
20
40
CM
, to assure
I = 5 mA
60
40 mA
35 mA
30 mA
25 mA
20 mA
15 mA
10 mA
F
F
80
,
O
20
,
100
Figure 2. Current transfer ratio vs. input
current.
Figure 5. Propagation delay vs. temperature.
6. The 1.9 k load represents 1 TTL unit load
7. The 4.1 k load represents 1 LSTTL unit
8. The frequency at which the ac output
9. Use of a 0.1 F bypass capacitor
2000
1500
1000
1.5
1.0
0.5
0.1
500
transient immunity in a Logic Low level is
the maximum tolerable (negative) dV
on the falling edge of the common mode
pulse signal, V
output will remain in a Logic Low state
(i.e., V
of 1.6 mA and the 5.6 k pull-up resistor.
load of 0.36 mA and the 6.1 k pull-up
resistor.
voltage is 3 dB below the low frequency
asymptote.
connected between pins 5 and 8 is
recommended.
0
0
-60
O
< 0.8 V).
I
F
T
A
– INPUT CURRENT – mA
I
HCPL-2530/0530 (R
HCPL-2531/0531/4534/0534
(R
HCPL-2530/0530
HCPL-2531/0531/4534/0534
-20
F
– TEMPERATURE – C
L
= 16 mA, V
CM
= 1.9 k )
1
t
, to assure that the
PLH
20
CC
NORMALIZED
I = 16 mA
V = 0.5 V
V
T = 25°C
F
A
t
O
CC
= 5.0 V
PHL
10
L
= 5 V
= 4.1 k )
60
CM
100
/dt
100
Figure 3. Input current vs. forward voltage.
Figure 6. Logic high output current vs.
temperature.
10. In accordance with UL 1577, each
11. In accordance with UL 1577, each
12. Measured between the LED anode and
13. Derate linearly above 90 C free-air
0.001
1000
10
10
10
10
0.01
10
10
100
10
1.0
optocoupler is proof tested by applying an
insulation test voltage 4500 V rms for 1
second (leakage detection current limit,
I
optocoupler is proof tested by applying an
insulation test voltage 6000 V rms for 1
second (leakage detection current limit,
I
cathode shorted together and pins 5
through 8 shorted together.
temperature at a rate of 3.0 mW/ C for
the SOIC-8 package.
0.1
10
I-O
I-O
+4
+3
+2
+1
-1
-2
0
1.1
-50
V
5 A).
5 A).
F
I
V
F
– FORWARD VOLTAGE – VOLTS
O
= 0
-25
= V
1.2
T
V
A
+
–
F
CC
I
– TEMPERATURE – °C
F
0
= 5.0 V
1.3
+25
1.4
T = 25°C
+50
A
1.5
+75 +100
1.6