5962-0420501HPC Avago Technologies US Inc., 5962-0420501HPC Datasheet
5962-0420501HPC
Specifications of 5962-0420501HPC
Related parts for 5962-0420501HPC
5962-0420501HPC Summary of contents
Page 1
... The products are capable of operation and storage over the full military temperature range and can be purchased as either commercial product, with full MIL-PRF-38534 Class H testing, or from Defense Supply Center Columbus (DSCC) Standard Microcircuit Drawing (SMD) 5962- 04205. All devices are manufactured and tested on a MIL-PRF-38534 certified line and are included in the DSCC Qualified Manufacturers List, QML-38534 for Hybrid Microcircuits. Schematic Diagram ...
Page 2
... 0.1 mF bypass capacitor must be connected between pins 5 and 8. Device Marking Avago DESIGNATOR A QYYWWZ HCPL-515x Avago P/N DSCC SMD* 5962-04205 SGP DSCC SMD* 01Hxx 50434 PIN ONE/ ESD IDENT * QUALIFIED PARTS ONLY Outline Drawing 9.40 (0.370) 9.91 (0.390) 0.76 (0.030) 1.27 (0.050) 0.51 (0.020) 3 ...
Page 3
Hermetic Optocoupler Options Option Description 00 Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial and hi-rel product (see drawings below for details). 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 00 Lead ...
Page 4
Absolute Maximum Ratings Parameter Symbol Storage Temperature Operating Temperature Case Temperature Junction Temperature Lead Solder Temperature Average Input Current Peak Transient Input Current (< ms pulse width, 300 pps) Reverse Input Voltage “High” Peak Output Current I OH (PEAK) “Low” ...
Page 5
Electrical Specifications (DC) Over recommended operating conditions ( Ground) unless otherwise specified. EE Parameter Symbol High Level Output Current I OH Low Level Output Current I OL High Level Output Voltage V OH Low Level Output Voltage V OL High Level Supply Current I CCH Low ...
Page 6
Switching Specifications (AC) Over recommended operating conditions ( Ground) unless otherwise specified. EE Parameter Symbol Propagation Delay Time t PLH to High Output Level Propagation Delay Time t PHL to Low Output Level Pulse Width Distortion PWD Propagation Delay Difference PDD Between Any Two Parts (t ...
Page 7
Package Characteristics Over recommended operating conditions (T Parameter Symbol Input-Output Leakage Current I I-O Resistance (Input-Output) R I-O Capacitance (Input-Output) C I-O *All typicals 25°C. A Notes: 1. Maximum pulse width = 10 ms, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with I minimum = 0.5 A. See Applications section for additional details on limiting I 2. Maximum pulse width = 50 ms, maximum duty cycle = 0.5 this test V is measured with a dc load current. When driving capacitive loads Maximum pulse width = 1 ms, maximum duty cycle = 20%. 5. This is a momentary withstand test, not an operating condition. 6. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together. 7. The difference between t and t ...
Page 8
18mA 100 30V -60 - 120 150 TEMPERATURE - C ...
Page 9
10mA 25˚ PLH 47Ω 3nF, PHL g g Duty Cycle = 50 10kHz 400 300 200 100 SUPPLY VOLTAGE ...
Page 10
Figure 17. I Test Circuit Figure 19. V Test Circuit ...
Page 11
500 Ω KHz 50% DUTY 3 CYCLE < Figure 23 and t Test ...
Page 12
Applications Information Eliminating Negative IGBT Gate Drive To keep the IGBT firmly off, the HCPL-5150 has a very low maximum V specification of 1.0 V. The HCPL-5150 OL realizes this very low V by using a DMOS transistor OL with 4 W (typical) ...
Page 13
V 1 270 Ω 2 CONTROL 3 INPUT 74XXX 4 OPEN COLLECTOR Figure 26. Typical Application Circuit with Negative IGBT Gate Drive P Parameter Description E I LED Current F V LED On Voltage F Duty Cycle Maximum LED ...
Page 14
CMR with the LED On (CMR ). H A high CMR LED drive circuit must keep the LED on during common mode transients. This is achieved by overdriving the LED current beyond the input threshold so that it is not pulled below ...
Page 15
I LED1 V OUT1 OFF V OUT2 I LED2 t PHL MAX t PLH MIN PDD* MAX = ( PHL PLH MAX PHL MAX Figure 33. Minimum LED Skew for Zero Dead ...
Page 16
... Data subject to change. Copyright © 006 Avago Technologies Limited. All rights reserved. 5989-0943EN - June , 007 MIL-PRF-38534 Class H and DSCC SMD Test Program Avago Technologies’ Hi-Rel Optocouplers are in compli- ance with MIL-PRF-38534 Class H. Class H devices are also in compliance with DSCC drawing 5962-04205. Testing consists of 100% screening and quality confor- mance inspection to MIL-PRF-38534. < 12.0) the optocou- ...