FOD063L Fairchild Optoelectronics Group, FOD063L Datasheet - Page 4

• Manufacturer Part Number: FOD063L
• Description: OPTOCOUPLER 2CH LOGIC 3.3V 8SOIC
• Manufacturer: Fairchild Optoelectronics Group

Specifications of FOD063L

• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 50mA
• Data Rate: 10Mbps
• Propagation Delay High - Low @ If: 75ns @ 7.5mA
• Current - Dc Forward (if): 15mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

©2008 Fairchild Semiconductor Corporation
FOD060L, FOD260L, FOD063L Rev. 1.0.3
Transfer Characteristics
Isolation Characteristics
** All typical values are at V
Notes
1. The V
2. Enable Input – No pull up resistor required as the device has an internal pull up resistor.
3. t
4. t
5. t
6. t
7. t
8. t
9. t
10. CM
11. CM
12. Device considered a two-terminal device: Pins 1,2,3 and 4 shorted together, and Pins 5,6,7 and 8 shorted together.
DC Characteristics
High Level Output Current
Low Level Output Voltage
Input Threshold Current
Characteristics
Input-Output
Insulation Leakage Current
Withstand Insulation Test
Voltage
Resistance (Input to Output)
Capacitance (Input to Output)
tantalum capacitor with good high frequency characteristic and should be connected as close as possible to the package V
GND pins of each device.
1.5V level on the LOW to HIGH transition of the output voltage pulse.
level on the HIGH to LOW transition of the output voltage pulse.
to the 1.5V level on the LOW to HIGH transition of the output voltage pulse.
to the 1.5V level on the HIGH to LOW transition of the output voltage pulse.
V
(i.e., V
PLH
PHL
PSK
r
f
ELH
EHL
OUT
– Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse.
– Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse.
H
L
– Propagation delay is measured from the 3.75 mA level on the LOW to HIGH transition of the input current pulse to the 1.5V
– Propagation delay is measured from the 3.75 mA level on the HIGH to LOW transition of the input current pulse to the
is the worst case difference between t
– Enable input propagation delay is measured from the 1.5V level on the HIGH to LOW transition of the input voltage pulse
– Enable input propagation delay is measured from the 1.5V level on the LOW to HIGH transition of the input voltage pulse
– The maximum tolerable rate of fall of the common mode voltage to ensure the output will remain in the low output state
– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the high state (i.e.,
CC
> 2.0 V). Measured in volts per microsecond (V/µs).
OUT
supply to each optoisolator must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic or solid
< 0.8 V). Measured in volts per microsecond (V/µs).
CC
= 3.3 V, T
(Relative humidity = 45%)
(V
(Note 2) V
(Note 2) V
(Note 2) V
I
I-O
(Note 12) ( t = 1 min.)
(f = 1 MHz) (Note 12)
Test Conditions Device
IO
(V
(I
(V
(T
F
(T
A
CC
= 500 V) (Note 12)
(V
(T
CC
= 250 µA, V
A
= 25°C
A
2 µA, R
I-O
A
= 3.3 V, V
= 25°C, t = 5 s)
= 3.3 V, I
= -40°C to +85°C Unless otherwise specified.)
= -40°C to +85°C Unless otherwise specified.)
= 3000 VDC)
PHL
E
E
E
T
= 2.0 V
= 2.0 V
= 2.0 V
A
(Note 12)
H
= 25°C)
and t
< 50%,
F
O
CC
= 5 mA, I
Test Conditions Symbol
= 0.6 V, I
PLH
= 3.3 V, V
for any devices at the stated test conditions.
Single Channel
Single Channel
Single Channel
FOD060L
FOD063L
FOD260L
OL
OL
4
O
= 13 mA)
= 13 mA)
= 3.3 V)
Symbol
V
R
C
I
I-O
ISO
I-O
I-O
V
I
I
OH
FT
OL
3750
5000
Min
Min
Typ**
10
0.6
Typ**
12
Max
1.0*
Max
0.6
50
5
www.fairchildsemi.com
Unit
V
Unit
µA
pF
RMS
mA
CC
µA
V
and