IL300-DEFG Vishay, IL300-DEFG Datasheet

Page 1

... IL300-DEFG-X007T (1) SMD-8, option 9 IL300-X009T IL300-DEFG-X009T VDE, UL 0.557 to 1.618 0.765 to 1.181 DIP-8 IL300-X001 IL300-DEFG-X001 DIP-8, 400 mil, IL300-X016 IL300-DEFG-X016 option 6 SMD-8, option 7 IL300-X017 IL300-DEFG-X017T SMD-8, option Note (1) Also available in tubes, do not put T on the end. Document Number: 83622 For technical questions, contact: Rev ...

Page 2

... The overall transfer gain is completely independent of the LED forward current. The IL300 transfer gain (K3) is expressed as the ratio of the output gain (K2) to the feedback gain (K1). This shows that the circuit gain becomes the product of the IL300 transfer gain times the ratio of the output to input resistors (R2/R1) ...

Page 3

... MHz NEP det MHz mA det mA det mA det mA det mA det optocoupleranswers@vishay.com IL300 Vishay Semiconductors VALUE UNIT 160 mW 2.13 mW/° 250 470 K/W 100 ° 0.65 mW/° 1500 K/W 100 °C 210 mW 2.8 mW/° 150 ° 100 °C > 5300 V RMS Ω 12 > 10 Ω 11 > ...

Page 4

... Category options: standard IL300 orders will be shipped from the categories that are available at the time of the order. Any of the ten categories may be shipped. For customers requiring a narrower selection of bins, the bins can be grouped together as follows: IL300-DEFG: order this part number to receive categories only. IL300-EF: order this part number to receive categories E, F only. ...

Page 5

... L ED Current (mA) F 1.010 Normalized to: 0 ° 1.005 ° °C 1.000 50 °C 75 °C 0.995 0.990 LED Current (mA) iil300_11 F Fig Normalized Transfer Gain vs. LED Current and Temperature mA, Mod = ± 2.0 Ma (peak kΩ kΩ Frequency (Hz) iil300_12 Fig Amplitude Response vs. Frequency www.vishay.com IL300 0° 100 ...

Page 6

... The output photodiode current can be directly or amplified to satisfy the needs of succeeding circuits. ISOLATED FEEDBACK AMPLIFIER The IL300 was designed to be the central element of DC coupled isolation amplifiers. Designing the IL300 into an amplifier that provides a feedback control signal for a line powered switch mode power is quite simple, as the following example will illustrate ...

Page 7

... Document Number: 83622 For technical questions, contact: Rev. 1.6, 10-Nov-10 Linear Optocoupler, High Gain Stability, Wide Bandwidth The value of R5 depends upon the IL300 Transfer Gain (K3 targeted unit gain device, however to minimize the part to part Transfer Gain variation, Infineon offers K3 R1 Voltage graded into ± ...

Page 8

... The AC characteristics are also quite impressive offering bandwidth of 100 kHz, with a - 45° phase shift at 80 kHz as shown in figure 16. optocoupleranswers@vishay.com R5 RESISTOR kΩ TYP. 0.59 51.1 0.66 45.3 ...

Page 9

... R3 R5 ( (R5 + R6) OUT = ( OUT Inverting = V R3 (R1 + R2) IN optocoupleranswers@vishay.com Vishay Semiconductors ). In these designs, R3 can be determined by the ref1 V V ref1 ref1 K1I P1 Fq 17098 + V ref2 – Vcc out – OFFSET ref1 V = ref2 (R5 + R6) K3 ref1 V = ref2 (R5 + R6) K3 ref1 V = ref2 ref1 V = ref2 R3 IL300 www.vishay.com 9 ...

Page 10

... PACKAGE MARKING (this is an example of the IL300-E-X001) www.vishay.com For technical questions, contact: 10 Linear Optocoupler, High Gain Stability, Wide Bandwidth permit operation close to ground. For best results, place a buffer transistor between the LED and output of the operational amplifier when a CMOS ...

Page 11

... Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part ...