MT16HTF12864HY-40EB3 Micron Technology Inc, MT16HTF12864HY-40EB3 Datasheet
![MODULE SDRAM DDR2 1GB 200SODIMM](/photos/7/83/78349/mfg_mt_sodimm_series_sml.jpg)
MT16HTF12864HY-40EB3
Specifications of MT16HTF12864HY-40EB3
Related parts for MT16HTF12864HY-40EB3
MT16HTF12864HY-40EB3 Summary of contents
Page 1
... DDR2 SDRAM SODIMM MT16HTF12864HY – 1GB MT16HTF25664HY – 2GB Features • 200-pin, small-outline dual in-line memory module (SODIMM) • Fast data transfer rates: PC2-3200, PC2-4200, PC2-5300, or PC2-6400 • 1GB (128 Meg x 64) or 2GB (256 Meg x 64) • 1.8V DD DDQ • 1.7–3.6V DDSPD • ...
Page 2
... The data sheet for the base device can be found on Micron’s Web site. Notes: 2. All part numbers end with a two-place code (not shown) that designates component and PCB revisions. Consult factory for current revision codes. Example: MT16HTF12864HY-40ED1. PDF: 09005aef818e4054 htf16c128_256x64h.pdf - Rev. D 3/10 EN ...
Page 3
Pin Assignments Table 5: Pin Assignments 200-Pin DDR2 SODIMM Front Pin Symbol Pin Symbol Pin DQS2 101 REF 103 DQ0 55 DQ18 105 7 DQ1 57 DQ19 107 9 V ...
Page 4
... Pin Descriptions The pin description table below is a comprehensive list of all possible pins for all DDR2 modules. All pins listed may not be supported on this module. See Pin Assignments for information specific to this module. Table 6: Pin Descriptions Symbol Type Ax Input BAx Input ...
Page 5
Table 6: Pin Descriptions (Continued) Symbol Type SDA I/O RDQSx, Output RDQS#x Err_Out# Output (open drain Supply DD DDQ V Supply DDSPD V Supply REF V Supply SS – NC – NF – NU – RFU PDF: 09005aef818e4054 ...
Page 6
Functional Block Diagram Figure 2: Functional Block Diagram S1# S0# DQS0# DQS0 DM0 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQS1# DQS1 DM1 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQS2# DQS2 DM2 DQ16 DQ17 DQ18 DQ19 DQ20 ...
Page 7
... DRAM core and eight corresponding n-bit-wide, one-half-clock-cycle data trans- fers at the I/O pins. DDR2 modules use two sets of differential signals: DQS, DQS# to capture data and CK and CK# to capture commands, addresses, and control signals. Differential clocks and data strobes ensure exceptional noise immunity for these signals and provide precise crossing points to capture input signals ...
Page 8
Electrical Specifications Stresses greater than those listed may cause permanent damage to the module. This is a stress rating only, and functional operation of the module at these or any other condi- tions outside those indicated in the device data ...
Page 9
... Design Considerations Simulations Micron memory modules are designed to optimize signal integrity through carefully de- signed terminations, controlled board impedances, routing topologies, trace length matching, and decoupling. However, good signal integrity starts at the system level. Mi- cron encourages designers to simulate the signal characteristics of the system's memo- ry bus to ensure adequate signal integrity of the entire memory system ...
Page 10
I Specifications DD Table 9: DDR2 I Specifications and Conditions – 1GB DD Values shown for MT47H64M8 DDR2 SDRAM only and are computed from values specified in the 512Mb (64 Meg x 8) component data sheet Parameter Operating one bank ...
Page 11
Table 9: DDR2 I Specifications and Conditions – 1GB (Continued) DD Values shown for MT47H64M8 DDR2 SDRAM only and are computed from values specified in the 512Mb (64 Meg x 8) component data sheet Parameter Operating bank interleave read current: ...
Page 12
Table 10: DDR2 I Specifications and Conditions – 2GB DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating one bank active-precharge current: ...
Page 13
Table 10: DDR2 I Specifications and Conditions – 2GB (Continued) DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating bank interleave read ...
Page 14
Serial Presence-Detect For the latest SPD data, refer to Micron's SPD page: www.micron.com/SPD. Table 11: SPD EEPROM Operating Conditions Parameter/Condition Supply voltage Input high voltage: logic 1; All inputs Input low voltage: logic 0; All inputs Output low voltage: I ...
Page 15
Module Dimensions Figure 3: 200-Pin DDR2 SODIMM 2.0 (0.079) R (2X) U2 1.80 (0.071) (2X) U6 6.00 (0.236) TYP Pin 1 2.00 (0.079) TYP 16.25 (0.64) TYP U11 U15 3.50 (0.138) TYP Pin 200 1. All dimensions are in millimeters ...