MT9HTF12872AY-40ED1 Micron Technology Inc, MT9HTF12872AY-40ED1 Datasheet - Page 16
![MODULE SDRAM DDR2 1GB 240DIMM](/photos/7/83/78383/mfg557-240-dimm_sml.jpg)
MT9HTF12872AY-40ED1
Manufacturer Part Number
MT9HTF12872AY-40ED1
Description
MODULE SDRAM DDR2 1GB 240DIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT9HTF12872AY-40ED1.pdf
(44 pages)
Specifications of MT9HTF12872AY-40ED1
Memory Type
DDR2 SDRAM
Memory Size
1GB
Speed
400MT/s
Package / Case
240-DIMM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power-Down Mode
CAS Latency (CL)
pdf: 09005aef80e6f860, source: 09005aef80e5b799
HTF9C32_64_128x72AG_2.fm - Rev. C 6/05 EN
Active power-down (PD) mode is defined by bit M12 as shown in Figure 5, Mode Register
(MR) Definition, on page 14. PD mode allows the user to determine the active power-
down mode, which determines performance vs. power savings. PD mode bit M12 does
not apply to precharge power-down mode.
When bit M12 = 0, standard Active Power-down mode or ‘fast-exit’ active power-down
mode is enabled. The
timing. The DLL is expected to be enabled and running during this mode.
When bit M12 = 1, a lower power active power-down mode or ‘slow-exit’ active power-
down mode is enabled. The
exit timing. The DLL can be enabled, but ‘frozen’ during active power-down mode since
the exit-to-READ command timing is relaxed. The power difference expected between
PD ‘normal’ and PD ‘low-power’ mode is defined in the I
The CAS Latency (CL) is defined by bits M4–M6 as shown in Figure 5, Mode Register
(MR) Definition, on page 14. CAS Latency is the delay, in clock cycles, between the regis-
tration of a READ command and the availability of the first bit of output data. The CAS
Latency can be set to 3, 4, or 5 clocks. CAS Latency of 2 clocks is a JEDEC optional feature
and may be enabled in future speed grades. DDR2 SDRAM devices do not support any
half clock latencies. Reserved states should not be used as unknown operation or
incompatibility with future versions may result.
DDR2 SDRAM devices also support a feature called Posted CAS additive latency (AL).
This feature allows the READ command to be issued prior to
internal command to the DDR2 SDRAM device by AL clocks. The AL feature is described
in more detail in the Extended Mode Register (EMR) and Operational sections.
Examples of CL = 3 and CL = 4 are shown in Figure 6, CAS Latency (CL); both assume AL
= 0. If a READ command is registered at clock edge n, and the CAS Latency is m clocks,
the data will be available nominally coincident with clock edge n + m (this assumes AL =
0).
256MB, 512MB, 1GB (x72, SR, ECC) 240-Pin DDR2 SDRAM UDIMM
t
XARD parameter is used for ‘fast-exit’ active power-down exit
t
XARDS parameter is used for ‘slow-exit’ active power-down
16
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003, 2004, 2005 Micron Technology, Inc. All rights reserved.
DD
table.
t
RCD(MIN) by delaying the
Mode Register (MR)